M32CSLASH8B datasheet(224/406 Pages) RENESAS

224 / 406 page

Under development

M32C/8B Group

17. Serial Interfaces

Preliminary specification

Specifications in this manual are tentative and subject to change.

REJ09B0450-0050 Rev.0.50 Oct 31, 2008

Page 207 of 385

17.1.1

Clock Synchronous Mode

Full-duplex clock synchronous serial communications are allowed in this mode. CTS/RTS function can be used

for transmit and receive control.

Table 17.1 lists specifications of clock synchronous mode. Table 17.2 lists pin settings. Figure 17.11 shows

selected. Figure 17.13 shows an example of a receive operation when an external clock is selected.

Table 17.1

Clock Synchronous Mode Specifications

NOTES:

1. Bits CNT3 to CNT0 in the TCSPR register select no division (n = 0) or divide-by-2n (n = 1 to 15).

2. If an external clock is selected, ensure that an “H” signal is applied to the CLKi pin when the CKPOL bit in the

UiC0 register is set to 0, and that an “L” signal is applied when the CKPOL bit is set to 1.

3. If an overrun error occurs, a read from the UiRB register returns undefined values. The IR bit in the SiRIC

Item

Specification

Data format

Data length: 8 bits long

Serial clock

Internal clock or external clock can be selected by the CKDIR bit in the UiMR register

(i = 0 to 4)

Baud rate

• When the CKDIR bit is set to 0 (internal clock):

fj / (2 (m + 1)

fj = f1, f8, f2n(1) m: setting value of the UiBRG register (00h to FFh)

• When the CKDIR bit is set to 1 (external clock): clock input to the CLKi pin

Transmit/receive control

Selectable among the CTS function, RTS function, or CTS/RTS function disabled

Transmit and receive

start condition

Internal clock is selected:

• Set the TE bit in the UiC1 register to 1 (transmit operation enabled)

• The TI bit in the UiC1 register is 0 (data in the UiTB register)

• Set the RE bit in the UiC1 register to 1 (receive operation enabled)

• “L” signal is applied to the CTSi pin when the CTS function is used

External clock is selected(2):

• Set the TE bit to 1

• The TI bit is 0

• Set the RE bit to 1

• The RI bit in the UiC1 register is 0 when the RTS function is used

When above 4 conditions are met, RTSi pin outputs “L”

If transmit-only operation is performed, the RE bit setting is not required in both cases.

Interrupt request

generation timing

Transmit interrupt (The UiIRS bit in the UiC1 register selects one of the following):

• The UiIRS bit is set to 0 (no data in the UiTB register):

when data is transferred from the UiTB register to the UARTi transmit shift register

(transmit operation started)

• The UiIRS bit is set to 1 (transmit operation completed):

when data transmit operation from the UARTi transmit shift register is completed

Receive interrupt:

• When data is transferred from the UARTi receive shift register to the UiRB register

(receive operation completed)

Error detection

• Overrun error(3)

Overrun error occurs when the 7th bit of the next data is received before reading the

UiRB register

Selectable function

• CLK polarity

Transmit data output timing and receive data input timing can be selected

• LSB first or MSB first

Data is transmitted and received from either bit 0 or bit 7

• Serial data logic inverse

Transmit and receive data are logically inverted

• Continuous receive mode

The TI bit becomes 0 by reading the UiRB register

M32C/8B датащи(PDF) 224 Page - Renesas Technology Corp

M32C/8B датащи(HTML) 224 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL