DG408LDY datasheet(6/12 Pages) VISHAY

6 / 12 page

www.vishay.com

Document Number: 71342

S-71241–Rev. E, 25-Jun-07

Vishay Siliconix

DG408L/409L

Notes:

a. Leakage parameters are guaranteed by worst case test condition and not subject to production test.

b. Room = 25 °C, Full = as determined by the operating temperature suffix.

c. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.

d. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.

e. Guaranteed by design, not subject to production test.

f. VIN = input voltage to perform proper function.

Δr

DS(on) = rDS(on) Max - rDS(on) Min.

h. Worst case isolation occurs on Channel 4 do to proximity to the drain pin.

i. rDS(on) flatness is measured as the difference between the minimum and maximum measured values across a defined Analog signal.

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation

of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum

rating conditions for extended periods may affect device reliability.

SPECIFICATIONS (SINGLE SUPPLY 3 V)

Parameter

Symbol

Test Conditions

Unless Otherwise Specified

V+ = 3 V, ± 10 %

, V- = 0 V

VEN = 0.4 V or 2.0 V

Tempb

Typd

A Suffix

- 55 to 125 °C

D Suffix

- 40 to 85 °C

Unit

Minc

Maxc

Minc

Maxc

Analog Switch

Analog Signal Rangee

VANALOG

Full

030

Drain-Source On-Resistance

rDS(on)

V+ = 2.7 V, VD = 0.5 or 2.2 V,

IS = 5 mA

Room

Full

105

100

Switch Off Leakage Currenta

IS(off)

V+ = 3.3 V, VS = 2 or 1 V, VD = 1 or 2 V

Room

Full

- 1

- 15

- 1

- 10

ID(off)

Room

Full

- 1

- 15

- 1

- 10

Channel On Leakage

Currenta

ID(on)

V+ = 3.3 V, VD = VS = 1 or 2 V

Sequence Each Switch On

Room

Full

- 1

- 15

- 1

- 10

Digital Control

Logic High Input Voltage

VINH

Full

Logic Low Input Voltage

VINL

Full

0.4

Input Currenta

IIN

VAX = VEN = 2.4 V or 0.4 V

Full

- 1.5

1.5

- 1

µA

Dynamic Characteristics

Transition Time

tTRANS

VS1 = 1.5 V, VS8 = 0 V, (DG408L)

VS1b = 1.5 V, VS4b = 0 V, (DG409L)

See Figure 2

Room

Full

150

175

150

175

Break-Before-Make Time

tOPEN

VS(all) = VDA = 1.5 V,

See Figure 4

Room

Full

Enable Turn-On Time

tON(EN)

VAX = 0 V, VS1 = 1.5 V (DG408L)

VAX = 0 V, VS1b = 1.5 V (DG409L)

See Figure 3

Room

Full

115

105

Enable Turn-Off Time

tOFF(EN)

Room

Full

100

115

100

105

Charge Injectione

CL = 1 nF, RGEN = 0 Ω, VGEN = 0 V

Room

0.4

Off Isolatione, h

OIRR

RL = 1 kΩ, f = 100 kHz

Room

- 70

Crosstalke

XTALK

Room

- 79

Source Off Capacitancee

CS(off)

f = 1 MHz, VS = 0 V, VEN = 0 V

Room

Drain Off Capacitancee

CD(off)

f = 1 MHz, VD = 0 V, VEN = 0 V

Room

Drain On Capacitancee

CD(on)

f = 1 MHz, VD = 0 V, VEN = 2 V

(DG409L only)

Room

DG408LDY датащи(PDF) 6 Page - Vishay Siliconix

DG408LDY датащи(HTML) 6 Page - Vishay Siliconix

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

датащи скачать

ссылки URL