M37207MF datasheet(32/122 Pages) RENESAS

32 / 122 page

MITSUBISHI MICROCOMPUTERS

M37207MF-XXXSP/FP, M37207M8-XXXSP

M37207EFSP/FP

SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER

and ON-SCREEN DISPLAY CONTROLLER

(3) I2C Clock Control Register

The I2C clock control register (address 00DD16) is used to set ACK

control, SCL mode and SCL frequency.

sBits 0 to 4: SCL Frequency Control Bits (CCR0–CCR4)

These bits control the SCL frequency. Refer to Figure 26.

sBit 5: SCL Mode Specification Bit (FAST MODE)

This bit specifies the SCL mode. When this bit is set to “0,” the stan-

dard clock mode is set. When the bit is set to “1,” the high-speed

clock mode is set.

sBit 6: ACK Bit (ACK BIT)

This bit sets the SDA status when an ACK clockVis generated. When

this bit is set to “0,” the ACK return mode is set and SDA goes to

LOW at the occurrence of an ACK clock. When the bit is set to “1,”

the ACK non-return mode is set. The SDA is held in the HIGH status

at the occurrence of an ACK clock.

However, when the slave address matches the address data in the

reception of address data at ACK BIT = “0,” the SDA is automatically

made LOW (ACK is returned). If there is a mismatch between the

slave address and the address data, the SDA is automatically made

HIGH (ACK is not returned).

V ACK clock: Clock for acknowledgement

sBit 7: ACK Clock Bit (ACK)

This bit specifies a mode of acknowledgment which is an acknowl-

edgment response of data transmission. When this bit is set to “0,”

the no ACK clock mode is set. In this case, no ACK clock occurs

after data transmission. When the bit is set to “1,” the ACK clock

mode is set and the master generates an ACK clock upon comple-

tion of each 1-byte data transmission.The device for transmitting

address data and control data releases the SDA at the occurrence of

an ACK clock (make SDA HIGH) and receives the ACK bit gener-

ated by the data receiving device.

Note: Do not write data into the I2C clock control register during

transmission. If data is written during transmission, the I2C

clock generator is reset, so that data cannot be transmitted

normally.

Fig. 26. I2C Clock Control Register

b7 b6 b5 b4 b3 b2 b1 b0

I2C clock control register (S2 : address 00DD16)

I2C Clock Control Register

SCL frequency control bits

(CCR0 to CCR4)

SCL mode

specification bit

(FAST MODE)

0 : Standard clock mode

1 : High-speed clock mode

Standard clock

mode

Name

Functions

After reset RW

ACK bit

(ACK BIT)

ACK clock bit

(ACK)

0 : ACK is returned.

1 : ACK is not returned.

0 : No ACK clock

1 : ACK clock

High speed

clock mode

Setup disabled Setup disabled

00 to 02

Setup disabled

333

Setup disabled

250

100

400 (See note)

83.3

166

500/CCR value

1000/CCR value

17.2

34.5

16.6

33.3

16.1

32.3

(at

φ = 4 MHz, unit : kHz)

Note: At 400 kHz in the high-speed clock mode, the duty is as below .

“0” period : “1” period = 3 : 2

In the other cases, the duty is as below.

“0” period : “1” period = 1 : 1

Setup value of

CCR4–CCR0

M37207MF датащи(PDF) 32 Page - Renesas Technology Corp

M37207MF датащи(HTML) 32 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL