PRODUCT DIMENSIONS

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

WDF550SAA

WDF550SAF

Electrical Requirements: 120-volt, 60- z, AC-only, 15- or

20-amp fused electrical supply. Copper wire only. A time-

delay fuse or circuit breaker and separate circuit is

recommended.

If direct wiring dishwasher: Use flexible, armored

, or

nonmetallic, sheathed copper wire

with grounding wire that meets the

wiring requirements for your home

and local codes and ordinances.

Use a UL Listed or CSA Approved strain relief.

If connecting dishwasher with a power supply cord:

Use Power Supply Cord Kit (Part

Number 4317824) marked for use

with dishwashers. Follow the kit instructions

for installing the power supply cord.

Power supply cord must plug into a grounded

3 prong, outlet, located in the cabinet next to

the dishwasher opening. Outlet must meet all

localcodes and ordinances.

Water Supply Requirements:A hot water line with 20 to

120 psi (138 to 862 kPa) water pressure. Watertemperature

must be 120°F (49°C) water at dishwasher.Use

³⁄₈" O.D.

copper tubing with compression fitting or flexible braided

water supply line (Part Number 4396897RP) (

¹⁄₂" minimum

plastic tubing is not recommended). Use a 90° elbow with

³⁄₄" hose connection with rubber washer. Do not solder

within 6" (15.2 cm) of the water inlet valve.

Drain Requirements:

I Use the new drain hose supplied with your dishwasher.

NOTE: If a longer drain hose is required:

I Use a new drain hose with maximum length of

10 ft (3 m) that meets all current AHAM/IAPMO

test standards.

I Use a new drain hose that is resistant to heat

and detergent

.

I Use a new drain hose that fits the 1" (2.5 cm)

drain connector on the dishwasher.

I

I

Connect drain hose to waste tee or disposal inlet

above drain trap in house plumbing.

Connect drain hose to house plumbing 20" (50.8 cm)

minimum above the floor.

NOTE: It is recommended that the drain hose either

be looped up and securely fastened to the underside

of the counter or be connected to an air gap.

I Use a drain air gap if the drain hose is connected

to house plumbing lower than 18" (45.7 cm) above

the subfloor or floor.

Drain Air Gap

I Use

¹⁄₂" (1.3 cm) minimum I.D. drain line fittings.

NOTE: Do not connect drain lines from other devices

to the dishwasher drain hose.

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

W10518038-D-WH

5/1/16

air gap

Side View

* To front of door frame

Rear View

24" (61 cm)*

16 5/8" (42.2 cm)

32

¹⁄₂" to 34¹⁄₂"

(82.6 to 87.6 cm)

23 5/9" (59.8 cm)

2

¹⁄₂" (6.2 cm)

CABINET CUTOUT DIMENSIONS

A. All surfaces free from intrusions

24" (61 cm)

minimum

34" to 35"

(86.4 cm to 88.9 cm)

24 (61 cm)

maximum

A

6"

(15.2 cm)

4"

(10.2

cm)

* Underside of countertop to floor

NOTES:

I Cut holes in shaded area of cabinet walls or floor for plumbing and electrical service.

I ADA installation – 32

¹⁄₂" (82.5 cm) beneath 34" (86.4 cm) high countertops may be

accomplished by adjusting the toekick and leveling legs.