COM200221 datasheet(34/82 Pages) SMSC

34 / 82 page

10 Mbps ARCNET (ANSI 878.1) Controller with 2Kx8 On-Chip RAM

Datasheet

Revision 09-27-07

Page 34

SMSC COM20022I

DATASHEET

6.2.5

Next ID Register

The Next ID Register is an 8-bit, read-only register, accessed when the sub-address bits are set up

accordingly (please refer to the Configuration Register and SUB ADR Register). The Next ID Register

holds the value of the Node ID to which the COM20022I will pass the token. When used in conjunction

with the Tentative ID Register, the Next ID Register can provide a complete network map. The Next ID

Each time the microsequencer updates the Next ID Register, a New Next ID interrupt is generated. This

bit is cleared by reading the Next ID Register. Default value is 0000 0000 upon hardware or software reset.

6.2.6

Status Register

The COM20022I Status Register is an 8-bit read-only register. All of the bits, except for bits 5 and 6, are

software compatible with previous SMSC ARCNET devices. In previous SMSC ARCNET devices the

Extended Timeout status was provided in bits 5 and 6 of the Status Register. In the COM20022I, the

COM20020, the COM90C66, and the COM90C165, COM20020-5, COM20051 and COM20051+ these

bits exist in and are controlled by the Configuration Register. The Status Register contents are defined as

in Table 6.3, but are defined differently during the Command Chaining operation. Please refer to the

Command Chaining section for the definition of the Status Register during Command Chaining operation.

The Status Register defaults to the value 1XX1 0001 upon either hardware or software reset.

6.2.7

Diagnostic Status Register

The Diagnostic Status Register contains seven read-only bits which help the user troubleshoot the network

or node operation. Various combinations of these bits and the TXEN bit of the Configuration Register

represent different situations. All of these bits, except the Excessive NAcK bit and the New Next ID bit, are

reset to logic "0" upon reading the Diagnostic Status Register or upon software or hardware reset. The

EXCNAK bit is reset by the "POR Clear Flags" command or upon software or hardware reset.

The

Diagnostic Status Register defaults to the value 0000 000X upon either hardware or software reset.

6.2.8

Command Register

Execution of commands are initiated by performing microcontroller writes to this register.

Any

combinations of written data other than those listed in Table 6.5 are not permitted and may result in

incorrect chip and/or network operation.

6.2.9

Address Pointer Registers

These read/write registers are each 8-bits wide and are used for addressing the internal RAM. New pointer

addresses should be written by first writing to the High Register and then writing to the Low Register

because writing to the Low Register loads the address. The contents of the Address Pointer High and Low

Registers are undefined upon hardware reset. Writing to Address Pointer low loads the address.

The DMAEN bit (new to the COM20022I) is located at bit 3 of the ADDRESS PTR HIGH register. The

DMAEN bit is used to Disable/Enable the assertion of the DMA Request (DREQ pin) after writing the

Address Pointer Low register. The SWAP bit (new to the COM20022I) is located at bit 0 of Address Pointer

Low register. The SWAP bit is used to swap the upper and lower data byte. When 16 bit access is enabled,

(W16=1), A0 becomes the SWAP bit.

COM200221 датащи(PDF) 34 Page - SMSC Corporation

COM200221 датащи(HTML) 34 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82

датащи скачать

ссылки URL