| поискавой системы для электроныых деталей |
|
IS25LE512MG-RLLA2:PTY датащи(PDF) 109 Page - Integrated Silicon Solution, Inc |
|
|
|||||||||||||||||||||||||||||
IS25LE512MG-RLLA2:PTY датащи(HTML) 109 Page - Integrated Silicon Solution, Inc |
|
109 / 194 page ![]() IS25LE512MG IS25WE512MG Integrated Silicon Solution, Inc.- www.issi.com 109 Rev. A6 10/02/2025 8.27 SET READ PARAMETERS OPERATION (SRPNV: 65h, SRPV: C0h/63h) Set Read Parameter Bits This device supports configurable burst length and dummy cycles in both SPI and QPI mode by setting three bits (P2, P1, P0) and four bits (P6, P5, P4, P3) within the Read Register, respectively. To set those bits the SRPNV and SRPV operation instruction are used. Details regarding burst length and dummy cycles can be found in Table 6.9, Table 6.10, and Table 6.11. HOLD#/RESET# function selection (P7) bit in the Read Register can be set with the SRPNV and SRPV operation as well, in order to select HOLD#/RESET# pin as RESET# or HOLD#. For the device with dedicated RESET# pin (or ball), RESET# pin (or ball) will be a separate pin (or ball) and it is independent of the P7 bit setting in Read Register. SRPNV is used to set the non-volatile Read Register, while SRPV is used to set the volatile Read Register. To write non-volatile Read Parameter bits, a standard Write Enable (06h) instruction must previously have been executed for the device to accept SRPNV(65h) instruction (Status Register bit WEL must equal “1”). To write volatile Read Parameter bits (SRPV), 63h or C0h command can be used. When using 63h instruction, a standard Write Enable (06h) instruction must previously have been executed for the device to accept SRPV (63h) instruction (Status Register bit WEL must equal “1”). But C0h instruction does not require a standard Write Enable (06h) operation. (Status Register bit WEL remains “0”). Note: When SRPNV is executed, the volatile Read Register is set as well as the non-volatile Read Register. Figure 8.60 Set Read Parameters Sequence In SPI Mode Instruction = 65h or C0h/63h CE # SCK SI SO Data In 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 3 Mode 0 7 3 2 1 0 6 5 4 High Impedence Figure 8.61 Set Read Parameters Sequence In QPI Mode 65h or C0h/63h 0 1 Mode 3 Mode 0 2 3 7:4 3:0 CE# SCK IO[3:0] Data In |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |