PI74LPT374CS datasheet(2/6 Pages) PERICOM

2 / 6 page

PS8503A

10/06/04

PI74LPT374

Fast CMOS 3.3V Octal D Flip-Flop

Storage Temperature ..........................................................–65°C to +150°C

Ambient Temperature with Power Applied .........................–40°C to +85°C

Supply Voltage to Ground Potential (Inputs & VCC Only)...–0.5V to +7.0V

Supply Voltage to Ground Potential (Outputs & D/O Only) –0.5V to +7.0V

DC Input Voltage ..................................................................–0.5V to +7.0V

DC Output Current............................................................................120 mA

Power Dissipation .................................................................................1.0W

Note:

Stresses greater than those listed under MAXIMUM RAT-

INGS may cause permanent damage to the device. This is a

stress rating only and functional operation of the device at

these or any other conditions above those indicated in the op-

erationalsectionsofthisspecificationisnotimplied. Exposure

to absolute maximum rating conditions for extended periods

may affect reliability.

Maximum Ratings

(Above which the useful life may be impaired. For user guidelines, not tested.)

DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 2.7V to 3.6V)

Parameters

Description

Test Conditions(1)

Min.

Typ(2) Max. Units

VIH

Input HIGH Voltage (Input pins)

Guaranteed Logic HIGH Level

2.2

5.5

Input HIGH Voltage

(I/O pins)

2.0

5.5

VIL

Input LOW Voltage

(Input and I/O pins)

Guaranteed Logic LOW Level

–0.5

0.8

IIH

Input HIGH Current (Input pins)

VCC = Max.

VIN= 5.5V

±1

µA

Input HIGH Current (I/O pins)

VCC = Max.

VIN = VCC

±1

IIL

Input LOW Current (Input pins)

VCC = Max.

VIN = GND

±1

Input LOW Current (I/O pins)

VCC = Max.

VIN = GND

±1

IOZH

High Impedance Output Current

VCC = Max.

VOUT = 5.5V

±1

IOZL

(3-State Output pins)

VCC = Max.

VOUT = GND

±1

VIK

Clamp Diode Voltage

VCC = Min., IIN = –18 mA

–0.7

–1.2

IODH

Output HIGH Current

VCC = 3.3V, VIN = VIH or VIL,

VO = 1.5V(3)

–36

–60

–110

IODL

Output LOW Current

VCC = 3.3V, VIN = VIH or VIL,

VO = 1.5V(3)

200

VOH

Output HIGH Voltage

VCC = Min.

VIN = VIH or VIL

IOH = –0.1 mA VCC-0.2

IOH = –3 mA

2.4

3.0

VCC = 3.0V,

VIN = VIH or VIL

IOH = –8 mA

2.4(5)

2.0

3.0

IOH = –24 mA

VOL

Output LOW Voltage

VCC = Min.

IOL = 0.1 mA

0.2

VIN = VIH or VIL

IOL = 16 mA

0.2

0.4

IOL = 24 mA

0.3

0.5

IOS

Short Circuit Current(4)

VCC = Max.(3), VOUT = GND

–60

–85

–240

IOFF

Power Down Disable

VCC = 0V, VIN or VOUT ≤ 4.5V

±100

µA

Input Hysteresis

150

Notes:

For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.

Typical values are at VCC = 3.3V, +25°C ambient and maximum loading.

Not more than one output should be shorted at one time. Duration of the test should not exceed one second.

This parameter is guaranteed but not tested.

VOH = VCC – 0.6V at rated current.

PI74LPT374CS датащи(PDF) 2 Page - Pericom Semiconductor Corporation

PI74LPT374CS датащи(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6

датащи скачать

ссылки URL