| поискавой системы для электроныых деталей |
|
PCA9625 датащи(PDF) 8 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCA9625 датащи(HTML) 8 Page - NXP Semiconductors |
|
8 / 33 page ![]() PCA9625_2 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 02 — 15 January 2008 8 of 33 NXP Semiconductors PCA9625 16-bit Fm+ I2C-bus 100 mA 24 V LED driver Remark: The Software Reset I2C-bus address is a reserved address and cannot be used as a regular I2C-bus slave address or as an LED All Call or LED Sub Call address. 7.2 Control register Following the successful acknowledgement of the slave address, LED All Call address or LED Sub Call address, the bus master will send a byte to the PCA9625, which will be stored in the Control register. The lowest 5 bits are used as a pointer to determine which register will be accessed (D[4:0]). The highest 3 bits are used as Auto-Increment flag and Auto-Increment options (AI[2:0]). When the Auto-Increment flag is set (AI2 = logic 1), the five low order bits of the Control register are automatically incremented after a read or write. This allows the user to program the registers sequentially. Four different types of Auto-Increment are possible, depending on AI1 and AI0 values. Remark: Other combinations not shown in Table 3 (AI[2:0] = 001, 010, and 011) are reserved and must not be used for proper device operation. Fig 4. Software Reset address 0 002aab416 0 0 0 0 0 1 1 R/W reset state = 80h Remark: The Control register does not apply to the Software Reset I2C-bus address. Fig 5. Control register Table 3. Auto-Increment options AI2 AI1 AI0 Function 0 0 0 no Auto-Increment 1 0 0 Auto-Increment for all registers. D[4:0] roll over to ‘0 0000’ after the last register (1 1011) is accessed. 1 0 1 Auto-Increment for individual brightness registers only. D[4:0] roll over to ‘0 0010’ after the last register (1 0001) is accessed. 1 1 0 Auto-Increment for global control registers only. D[4:0] roll over to ‘1 0010’ after the last register (1 0011) is accessed. 1 1 1 Auto-Increment for individual and global control registers only. D[4:0] roll over to ‘0 0010’ after the last register (1 0011) is accessed. 002aac147 AI2 AI1 AI0 D4 D3 D2 D1 D0 Auto-Increment flag register address Auto-Increment options |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |