HIP4080A

FN3658 Rev.8.00

Page 4 of 19

Dec 11, 2019

Absolute Maximum Ratings

Thermal Information

Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . . -0.3V to 16V

Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V

Voltage on AHS, BHS . . . -6.0V (Transient) to 80V (25°C to 125°C)

Voltage on AHS, BHS . . . -6.0V (Transient) to 70V (-55°C to 125°C)

Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient)

Voltage on AHB, BHB . . . . . . VAHS, BHS -0.3V to VAHS, BHS +VDD

Voltage on ALO, BLO. . . . . . . . . . . . VALS, BLS -0.3V to VCC +0.3V

Voltage on AHO, BHO . . . . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V

Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA

Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns

All Voltages relative to VSS, unless otherwise specified.

Operating Conditions

Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . +9.5V to +15V

Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V

Voltage on AHB, BHB . . . . . . . VAHS, BHS +5V to VAHS, BHS +15V

Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . -500µA to -50µA

Operating Ambient Temperature Range . . . . . . . . . .-40°C to +85°C

Thermal Resistance (Typical, Note 3)

JA (°C/W)

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

85

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

75

Maximum Power Dissipation at +85°C

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .470mW

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .530mW

Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C

Operating Max. Junction Temperature. . . . . . . . . . . . . . . . . . +125°C

Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300°C

(For SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTE:

3.

JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Electrical Specifications VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100K, and

TA = +25°C, Unless Otherwise Specified

PARAMETERS

SYMBOL

TEST CONDITIONS

TJ = +25°C

TJ = - 40°C

TO +125°C

UNITS

MIN

TYP

MAX

MIN

MAX

SUPPLY CURRENTS AND CHARGE PUMPS

VDD Quiescent Current

IDD

IN- = 2.5V, Other Inputs = 0V

8

11

14

7

14

mA

VDD Operating Current

IDDO

Outputs switching f = 500kHz, No Load

9

12

15

8

15

mA

VCC Quiescent Current

ICC

IN- = 2.5V, Other Inputs = 0V,

IALO = IBLO = 0

-

25

80

-

100

A

VCC Operating Current

ICCO

f = 500kHz, No Load

1

1.25

2.0

0.8

3

mA

AHB, BHB Quiescent Current -

Qpump Output Current

IAHB, IBHB IN- = 2.5V, Other Inputs = 0V,

IAHO =IBHO = 0,

VDD = VCC =VAHB = VBHB = 10V

-50

-25

-11

-60

-10

A

AHB, BHB Operating Current

IAHBO,

IBHBO

f = 500kHz, No Load

0.62

1.2

1.5

0.5

1.9

mA

AHS, BHS, AHB, BHB Leakage Current

IHLK

VBHS = VAHS = 80V,

VAHB = VBHB = 93V

-

0.02

1.0

-

10

A

AHB-AHS, BHB-BHS Qpump

Output Voltage

VAHB -

VAHS

VBHB -

VBHS

IAHB = IAHB = 0, No Load

11.5

12.6

14.0

10.5

14.5

V

INPUT COMPARATOR PINS: IN+, IN-, OUT

Offset Voltage

VOS

Over Common Mode Voltage Range

-10

0

+10

-15

+15

mV

Input Bias Current

IIB

00.5

2

0

4

A

Input Offset Current

IOS

-1

0

+1-2+2

A

Input Common Mode Voltage Range

CMVR

1

-

VDD

-1.5

1VDD

-1.5

V