2

®

PCM56

DIGITAL INPUT

Resolution

16

Bits

Digital Inputs(1): VIH

+2.4

+VL

V

VIL

0

+0.8

V

IIH, VIN = +2.7V

+1.0

µA

IIL, VIN = +0.4V

–50

µA

Input Clock Frequency

10.0

MHz

TRANSFER CHARACTERISTICS

ACCURACY

Gain Error

±2.0

%

Bipolar Zero Error

±30

mV

Differential Linearity Error

±0.001

% of FSR(2)

Noise (rms, 20Hz to 20kHz) at Bipolar Zero (VOUT models)

6

µV

TOTAL HARMONIC DISTORTION

VO = ±FS at f = 991Hz: PCM56P-K

–94

–92

dB

PCM56P-J

–94

–88

dB

PCM56P, PCM56U

–94

–82

dB

PCM56P-L

–94

–80

dB

VO = –20dB at f = 991Hz: PCM56P-K

–75

–74

dB

PCM56P-J

–75

–68

dB

PCM56P, PCM56U

–75

–68

dB

PCM56P-L

–75

–60

dB

VO = –60dB at f = 991Hz: PCM56P-K

–35

–34

dB

PCM56P-J

–35

–28

dB

PCM56P, PCM56U

–35

–28

dB

PCM56P-L

–35

–20

dB

MONOTONICITY

15

Bits

DRIFT (0

°C to +70°C)

Total Drift(3)

±25

ppm of FSR/

°C

Bipolar Zero Drift

±4

ppm of FSR/

°C

SETTLING TIME (to

±0.006% of FSR)

Voltage Output: 6V Step

1.5

µs

1LSB

1.0

µs

Slew Rate

10

V/

µs

Current Output, 1mA Step: 10

Ω to 100Ω Load

350

ns

1k

Ω Load(4)

350

ns

WARM-UP TIME

1Min

OUTPUT

Voltage Output Configuration: Bipolar Range

±3.0

V

Output Current

±2.0

mA

Output Impedance

0.10

Ω

Short Circuit Duration

Current Output Configuration:

Bipolar Range (

±30%)

±1.0

mA

Output Impedance (

±30%)

1.2

k

Ω

POWER SUPPLY REQUIREMENTS(5)

Voltage: +VS and +VL

+4.75

+5.00

+13.2

V

–VS and –VL

–4.75

–5.00

–13.2

V

Supply Drain (No Load): +V (+VS and +VL = +5V)

+10.00

+17.0

mA

–V (–VS and –VL = –5V)

–25.0

–35.0

mA

+V (+VS and +VL = +12V)

+12.0

mA

–V (–VS and –VL = –12V)

–27.0

mA

Power Dissipation: VS and VL = ±5V

175

260

mW

VS and VL = ±12V

468

mW

TEMPERATURE RANGE

Specification

0

+70

°C

Operation

–25

+70

°C

Storage

–60

+100

°C

NOTES: (1) Logic input levels are TTL/CMOS-compatible. (2) FSR means full-scale range and is equivalent to 6V (

±3V) for PCM56 in the V

OUT mode. (3) This is the

combined drift error due to gain, offset, and linearity over temperature. (4) Measured with an active clamp to provide a low impedance for approximately 200ns. (5) All

specifications assume +VS connected to +VL and –VS connected to –VL. If supplies are connected separately, –VL must not be more negative than –VS supply voltage

to assure proper operation. No similar restriction applies to the value of +VL with respect to +VS.

PCM56U, PCM56P-J, -K

PARAMETER

MIN

TYP

MAX

UNITS

SPECIFICATIONS

ELECTRICAL

Typical at +25

°C, and nominal power supply voltages ±5V, unless otherwise noted.

Indefinite to Common