LMV761, LMV762, LMV762Q-Q1

SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

www.ti.com

2.7-V Electrical Characteristics (continued)

Unless otherwise specified, all limited ensured for TJ = 25°C, VCM = V

+ / 2, V+ = 2.7 V, V− = 0 V−.

PARAMETER

TEST CONDITIONS

MIN(1)

TYP(2)

MAX(1)

UNIT

Supply current LMV761

275

700

μA

(single comparator)

IS

550

LMV762, LMV762Q-Q1 (both

μA

comparators)

apply at the temperature extremes(3)

1400

IOUT LEAKAGE

Output leakage I at shutdown SD = GND, VO = 2.7 V

0.2

μA

Supply leakage I at

IS LEAKAGE

SD = GND, VCC = 2.7 V

0.2

2

μA

shutdown

6.7

5-V Electrical Characteristics

Unless otherwise specified, all limited ensured for TJ = 25°C, VCM = V

+ / 2, V+ = 5 V, V− = 0 V−.

PARAMETER

TEST CONDITIONS

MIN(1)

TYP(2)

MAX(1)

UNIT

0.2

VOS

Input offset voltage

mV

apply at the temperature extremes(3)

1

IB

Input bias current(4)

0.2

50

pA

IOS

Input offset current(4)

0.01

5

pA

Common-mode rejection

CMRR

0 V < VCM < VCC – 1.3 V

80

100

dB

ratio

PSRR

Power supply rejection ratio

V+ = 2.7 V to 5 V

80

110

dB

Input common-mode voltage

apply at the temperature

CMVR

CMRR > 50 dB

−0.3

3.8

V

range

extremes(3)

Output swing high

IL = 4 mA, VID = 200 mV

V+ – 0.35

V+ – 0.1

V

VO

Output swing low

IL = –4 mA, VID = –200 mV

120

250

mV

Sourcing, VO = 2.5 V, VID = 200 mV

6

60

ISC

Output short circuit current(5)

mA

Sinking, VO = 2.5 V, VID = −200 mV

6

40

Supply current LMV761

225

700

μA

(single comparator)

IS

450

LMV762, LMV762Q-Q1

μA

(both comparators)

apply at the temperature extremes(3)

1400

Output leakage I at

IOUT LEAKAGE

SD = GND, VO = 5 V

0.2

μA

shutdown

Supply leakage I at

IS LEAKAGE

SD = GND, VCC = 5 V

0.2

2

μA

shutdown

(1)

All limits are specified by testing or statistical analysis.

(2)

Typical values represent the most likely parametric norm.

(3)

Maximum temperature ensured range is

−40°C to +125°C.

(4)

Specified by design.

(5)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical

tables under conditions of internal self-heating where TJ > TA. See Recommended Operating Conditions for information on temperature

de-rating of this device. Absolute Maximum Rating indicate junction temperature limits beyond which the device may be permanently

degraded, either mechanically or electrically.

6

Submit Documentation Feedback

Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1