THS6012

www.ti.com

SLOS226F – SEPTEMBER 1998 – REVISED JUNE 2012

ELECTRICAL CHARACTERISTICS (continued)

VCC = ±15 V, RL = 25 Ω, RF = 1 kΩ, TA = 25°C (unless otherwise noted)

PARAMETER

TEST CONDITIONS(1)

MIN

TYP

MAX

UNIT

VO(PP) = 20 V

-65

VCC = ±15 V,

RF = 680 Ω,

G = 2,

f = 1 MHz

VO(PP) = 2 V

-79

THD

Total harmonic distortion

dBc

VCC = ±5 V,

RF = 680 Ω,

VO(PP) = 2 V

-76

G = 2,

f = 1 MHz

VCC = ±5 V or ±15 V, f = 10 kHz, G = 2, Single-

Vn

Input voltage noise

1.7

nV/

√Hz

ended

Positive (IN+)

11.5

Input noise

In

VCC = ±5 V or ±15 V, f = 10 kHz, G = 2

pA/

√Hz

current

Negative (IN-)

16

VCC = ±5 V

0.04%

G = 2,

NTSC, 40 IRE

AD

Differential gain error

RL = 150 Ω,

Modulation

VCC = ±15 V

0.05%

VCC = ±5 V

0.07°

G = 2,

NTSC, 40 IRE

φD

Differential phase error

RL = 150 Ω,

Modulation

VCC = ±15 V

0.08°

Crosstalk

Driver to driver

VI = 200 mV,

f = 1 MHz

-62

dB

DC PERFORMANCE

VCC = ±5 V

1.5

Open loop transresistance

M

Ω

VCC = ±15 V

5

TA = 25°C

2

5

VIO

Input offset voltage

VCC = ±5 V or ±15 V

mV

TA = full range

7

Input offset voltage drift

VCC = ±5 V or ±15 V,

TA = full range

20

μV/°C

TA = 25°C

1.5

4

Differential input offset voltage

VCC = ±5 V or ±15 V

mV

TA = full range

5

TA = 25°C

3

9

Negative

μA

TA = full range

12

TA = 25°C

4

10

IIB

Input bias current

Positive

VCC = ±5 V or ±15 V

μA

TA = full range

12

TA = 25°C

1.5

8

Differential

μA

TA = full range

11

Differential input offset voltage drift VCC = ±5 V or ±15 V,

TA = full range

10

μV/°C

INPUT CHARACTERISTICS

VCC = ±5 V

±3.6

±3.7

Common-mode input voltage

VICR

V

range

VCC = ±15 V

±13.4

±13.5

Common-mode rejection ratio

62

70

CMRR

VCC = ±5 V or ±15 V,

TA = full range

dB

Differential common-mode

100

rejection ratio

RI

Input resistance

300

k

Ω

CI

Differential input capacitance

1.4

pF

OUTPUT CHARACTERISTICS

3 to

3.2 to

VCC = ±5 V

-2.8

-3

Single ended

RL = 25 Ω

V

11.8 to -

12.5 to -

VCC = ±15 V

11.5

12.2

Output voltage

VO

swing

6 to

6.4 to

VCC = ±5 V

-5.6

-6

Differential

RL = 50 Ω

V

23.6 to -

25 to -

VCC = ±15 V

23

24.4

RL = 5 Ω,

VCC = ±5 V

500

IO

Output current(2)

mA

RL = 25 Ω,

VCC = ±15 V

400

500

(2)

A heat sink is required to keep the junction temperature below absolute maximum when an output is heavily loaded or shorted. See

absolute maximum ratings and Thermal Information section.

Copyright © 1998–2012, Texas Instruments Incorporated

5