LP Series

Nonincendive Magnetic Encoder Models : HH_9/AH_9/ HH_B/AH_B

HX_9/AX_9/HX_B/AX_B

SPECIAL CONDITIONS FOR SAFE USE

The equipment shall be installed in an enclosure that provides a degree of protection not less than IP54 in accordance with IEC/EN

60079-15.

Provision must be made to prevent the rated voltage being exceeded by transients of more than 140%. Power with (NEC) Class 2

supply.

Encoders are intended to be used in an area of not more than pollution degree 2

ASSEMBLY CAUTION: DO NOT OPEN WHEN ENERGIZED

For electrical installation use the standard EN/IEC 60079-14.

For maintenance, use the standard EN 60079-17.

The encoder must be returned to the manufacturer for repair or service. The unit is factory sealed and there are no adjustments or

maintenance required.

Electrical Ratings: 4.75-30Vdc, 7.6VA max

EU Declaration of Conformity

UL Declaration of Conformity

Models HH_9, HX_9, AH_9, AX_9, HH_B, HX_B, AH_B and AX_B non-sparking/nonincendive variations are recognized components which

comply with the following standards as defined in UL File E78446, Vol. 4 and shall be marked: Class I, Div. 2, Groups A,B,C,D and

-40°C to +85° and T4

UL 121201, 9th Edition, Rev 2017-09-15, Nonincendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Divisions 1 and 2

Hazardous (Classified) Locations

UL 508, 17th Ed., Rev. 2010-04-15, Industrial Control Equipment

CSA C22.2 No. 213-17, 3rd Edition, Sept-2017, Nonincendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Divisions 1

and 2 Hazardous (Classified) Locations

CAN/CSA C22.2 No. 14-10, 11th Ed., Rev. 2011-08-01, Industrial Control Equipment

The notified organization responsible for the follow-up inspections for this UL recognized product is (assessed by):

UL International (France) SA

Espace Technologique de Saint-Aubin, Immeuble Explorer

Route de l’Orme des Merisiers – F-91190 SAINT AUBIN

Identification No. 675

NI Installation sheet AH_9/HH_9/AH_B/HH_B - P/N 2000/013 Rev. B

UL – ATEX – IECEx certified

BEI SENSORS Europe

9, rue de Copenhague

Espace Européen de l’Entreprise-Schiltigheim

BP 70044 - 67013 STRASBOURG Cedex France

Tel: +33 (0)3-88-20-80-80 | Fax: +33 (0)3-88-20-87-87

email: info@beisensors.com

BEI SENSORS North America

1461 Lawrence Dr | Thousand Oaks, CA 91320 USA

Tel: 800-350-2727 or 805-716-0322

Fax: 800-960-2726 or 805-968-3154

email: beisales@beisensors.com

www.beisensors.com

BEI Sensors, certifies that non-sparking Models HH_9, HX_9, AH_9, AX_9, HH_B, HX_B, AH_B and AX_B and all resolutions, channel and

output type options as noted on the IECEx and DEMKO certificates cited below,

With the following inscriptions:

II 3 G Ex nA IIC T4 Gc

Designed and manufactured to comply with these directives: ATEX: 2014/34/EU and EMC: 2014/30/EU

Complies with these standards:

ATEX: EN60079-0:2018, EN60079-15:2010,

IECEx: IEC60079-0:2017, IEC60079-15:2010

A comparative study of the standards EN 60079-0 (2012+A11 2013 and 2018), shows that the product is not concerned by the

substantial modifications.

As detailed in EC type examination certificates: DEMKO 17 ATEX 1877X and IECEx UL 17.0043X

Product Quality Assurance Notification: LCIE 03 ATEX Q8060

Product Quality Assurance Report: FR/LCI/QAR08.0002

The following standards were also investigated for this certification: EN 60-529, NFC 23-520, NFC 23-539, EN 50081-1, EN 55022 classe

B, EN 55014, EN 61000-6-2, CEI 61000-4-2, CEI 61000-4-3, CEI61000-4-4, CEI 61000-4-5, CEI 61000-4-6, CEI 61000-4-8, CEI 61000-4-11

The notified organization responsible for the follow-up of the ATEX directive is (assessed by):

LCIE, B.P.8, F92260 Fontenay-aux-Roses

Identification No. 0081

The company in charge of certification CEM is:

LCIE BUREAU VERITAS,

Aire de la Thur 68840 Pulversheim

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•