| поискавой системы для электроныых деталей |
|
LT3591 датащи(PDF) 3 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LT3591 датащи(HTML) 3 Page - Linear Technology |
|
3 / 24 page ![]() LT3498 3 3498f Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3498 is guaranteed to meet performance specifications from 0°C to 85°C. Specifications over the –40°C to 85°C junction operating temperature range are assured by design, characterization and correlation with statistical process controls. PARAMETER CONDITIONS MIN TYP MAX UNITS Switch Leakage Current VSW1 = 16V 0.1 5 µA CAP1 Pin Overvoltage Protection 26 27 28 V Schottky Forward Voltage ISCHOTTKY1 = 100mA 0.8 V Schottky Reverse Leakage VREVERSE1 = 20V 6 µA OLED Driver Feedback Voltage VCTRL2 = 3V (Note 3) ● 1.18 1.215 1.25 V Feedback Resistor ● 177 182 186 kΩ Minimum Switch Off Time After Start-Up 150 ns Minimum Switch Off Time During Start-Up (Note 4) 1 µs Maximum Switch Off Time VFB2 = 1.5V ● 15 20 30 µs Switch Current Limit 180 300 400 mA Switch VCESAT ISW2 = 200mA 260 mV Switch Leakage Current VSW2 = 16V 0.1 5 µA Schottky Forward Voltage ISCHOTTKY2 = 100mA 800 mV Schottky Reverse Leakage VREVERSE2 = 20V 2 µA PMOS Disconnect VCAP2 – VOUT2 IOUT2 = 10mA, VCAP2 = 5V 250 mV CTRL2 to FB2 Offset VCTRL2 = 0.5V 8 15 mV Maximum Shunt Current VFB2 = 1.3V 220 µA ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C, VIN = 3V, VCTRL1 = VCTRL2 = 3V. Note 3: Internal reference voltage is determined by finding VFB2 voltage level which causes quiescent current to increase 20µA above “Not Switching” level. Note 4: If CTRL2 is overriding the internal reference, start-up mode occurs when VFB2 is less then half the voltage on CTRL2. If CTRL2 is not overriding the internal reference, start-up mode occurs when VFB2 is less then half the voltage of the internal reference. |
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |