ADS5411IPGPR datasheet(7/24 Pages) TI2

7 / 24 page

ADS5411

SLAS487A − SEPTEMBER 2005 − REVISED JANUANRY 2010

www.ti.com

DEFINITION OF SPECIFICATIONS

Analog Bandwidth

The analog input frequency at which the power of the

fundamental is reduced by 3 dB with respect to the low

frequency value.

Aperture Delay

The delay in time between the rising edge of the input

sampling clock and the actual time at which the

sampling occurs.

Aperture Uncertainty (Jitter)

The sample-to-sample variation in aperture delay.

Clock Pulse Width/Duty Cycle

The duty cycle of a clock signal is the ratio of the time

the clock signal remains at a logic high (clock pulse

width) to the period of the clock signal. Duty cycle is

typically expressed as a percentage. A perfect

differential sine wave clock results in a 50% duty cycle.

Maximum Conversion Rate

The maximum sampling rate at which certified

operation is given. All parametric testing is performed

at this sampling rate unless otherwise noted.

Minimum Conversion Rate

The minimum sampling rate at which the ADC

functions.

Differential Nonlinearity (DNL)

An ideal ADC exhibits code transitions at analog input

values spaced exactly 1 LSB apart. The DNL is the

deviation of any single step from this ideal value,

measured in units of LSB.

Integral Nonlinearity (INL)

The INL is the deviation of the ADC’s transfer function

from a best fit line determined by a least squares curve

fit of that transfer function, measured in units of LSB.

Gain Error

The gain error is the deviation of the ADC’s actual input

full-scale range from its ideal value. The gain error is

given as a percentage of the ideal input full-scale range.

Offset Error

The offset error is the difference, given in number of

LSBs, between the ADC’s actual value average idle

channel output code and the ideal average idle channel

output code. This quantity is often mapped into mV.

PSRR

The maximum change in offset voltage divided by the

total change in supply voltage, in units of mV/V.

Temperature Drift

The temperature drift coefficient (with respect to gain

error and offset error) specifies the change per degree

Celsius of the parameter from TMIN or TMAX. It is

computed as the maximum variation of that parameter

over the whole temperature range divided by TMAX −

TMIN.

Signal-to-Noise Ratio (SNR)

SNR is the ratio of the power of the fundamental (PS)

to the noise floor power (PN), excluding the power at dc

and the first five harmonics.

SNR

+ 10Log

SNR is either given in units of dBc (dB to carrier) when

the absolute power of the fundamental is used as the

reference or dBFS (dB to full scale) when the power of

the fundamental is extrapolated to the converter’s

full-scale range.

Signal-to-Noise and Distortion (SINAD)

SINAD is the ratio of the power of the fundamental (PS)

to the power of all the other spectral components

including noise (PN) and distortion (PD), but excluding

dc.

SINAD

+ 10Log

) P

SINAD is either given in units of dBc (dB to carrier) when

the absolute power of the fundamental is used as the

reference or dBFS (dB to full scale) when the power of

the fundamental is extrapolated to the converter’s

full-scale range.

Total Harmonic Distortion (THD)

THD is the ratio of the fundamental power (PS) to the

power of the first five harmonics (PD).

THD

+ 10Log

THD is typically given in units of dBc (dB to carrier).

Power Up Time

The difference in time from the point where the supplies

are stable at

±5% of the final value, to the time the ac

test is past.

ADS5411IPGPR датащи(PDF) 7 Page - Texas Instruments

ADS5411IPGPR датащи(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

датащи скачать

ссылки URL