SC312XDP512F0MPVR datasheet(175/1350 Pages) FREESCALE

175 / 1350 page

Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV3)

MC9S12XDP512 Data Sheet, Rev. 2.17

Freescale Semiconductor

175

5.3.2.7

ATD Status Register 0 (ATDSTAT0)

This read-only register contains the sequence complete ﬂag, overrun ﬂags for external trigger and FIFO

mode, and the conversion counter.

Read: Anytime

Write: Anytime (No effect on (CC2, CC1, CC0))

76543210

SCF

ETORF

FIFOR

CC2

CC1

CC0

Reset

00000000

= Unimplemented or Reserved

Figure 5-9. ATD Status Register 0 (ATDSTAT0)

Table 5-17. ATDSTAT0 Field Descriptions

Field

Description

SCF

Sequence Complete Flag — This ﬂag is set upon completion of a conversion sequence. If conversion

sequences are continuously performed (SCAN = 1), the ﬂag is set after each one is completed. This ﬂag is

cleared when one of the following occurs:

A) Write “1” to SCF

B) Write to ATDCTL5 (a new conversion sequence is started)

C) If AFFC=1 and read of a result register

0 Conversion sequence not completed

1 Conversion sequence has completed

ETORF

External Trigger Overrun Flag — While in edge trigger mode (ETRIGLE = 0), if additional active edges are

detected while a conversion sequence is in process the overrun ﬂag is set. This ﬂag is cleared when one of the

following occurs:

A) Write “1” to ETORF

B) Write to ATDCTL2, ATDCTL3 or ATDCTL4 (a conversion sequence is aborted)

C) Write to ATDCTL5 (a new conversion sequence is started)

0 No External trigger over run error has occurred

1 External trigger over run error has occurred

FIFOR

FIFO Over Run Flag — This bit indicates that a result register has been written to before its associated

conversion complete ﬂag (CCF) has been cleared. This ﬂag is most useful when using the FIFO mode because

the ﬂag potentially indicates that result registers are out of sync with the input channels. However, it is also

practical for non-FIFO modes, and indicates that a result register has been over written before it has been read

(i.e., the old data has been lost). This ﬂag is cleared when one of the following occurs:

A) Write “1” to FIFOR

B) Start a new conversion sequence (write to ATDCTL5 or external trigger)

0 No over run has occurred

1 An over run condition exists

2–0

CC[2:0]

Conversion Counter — These 3 read-only bits are the binary value of the conversion counter. The conversion

counter points to the result register that will receive the result of the current conversion. E.g. CC2 = 1, CC1 = 1,

CC0 = 0 indicates that the result of the current conversion will be in ATD result register 6. If in non-FIFO mode

(FIFO = 0) the conversion counter is initialized to zero at the begin and end of the conversion sequence. If in

FIFO mode (FIFO = 1) the register counter is not initialized. The conversion counters wraps around when its

maximum value is reached.

Aborting a conversion or starting a new conversion by write to an ATDCTL register (ATDCTL5-0) clears the

conversion counter even if FIFO=1.

SC312XDP512F0MPVR датащи(PDF) 175 Page - Freescale Semiconductor, Inc

SC312XDP512F0MPVR датащи(HTML) 175 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL