поискавой системы для электроныых деталей
  Russian  ▼
ALLDATASHEETRU.COM

X  

TLV1921 датащи(PDF) 13 Page - Texas Instruments

номер детали TLV1921
подробное описание детали  TLV192x Family of 65V Comparators with Integrated 2.5V Voltage Reference
PDF  26 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
производитель  TI [Texas Instruments]
домашняя страница  http://www.ti.com
Logo TI - Texas Instruments

TLV1921 датащи(HTML) 13 Page - Texas Instruments

Back Button TLV1921 Datasheet HTML 9Page - Texas Instruments TLV1921 Datasheet HTML 10Page - Texas Instruments TLV1921 Datasheet HTML 11Page - Texas Instruments TLV1921 Datasheet HTML 12Page - Texas Instruments TLV1921 Datasheet HTML 13Page - Texas Instruments TLV1921 Datasheet HTML 14Page - Texas Instruments TLV1921 Datasheet HTML 15Page - Texas Instruments TLV1921 Datasheet HTML 16Page - Texas Instruments TLV1921 Datasheet HTML 17Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 26 page
background image
The following is a summary of input voltage range conditions and the outcomes:
1. When both IN- and IN+ are within the common mode voltage range:
a. If IN- is greater than IN+ and the offset voltage, the output is low.
b. If IN- is less than IN+ and the offset voltage, the output is high.
c. If IN- is equal to IN+, the output state is technically indeterminite and output state is determined by the
random polarity of the internal offset votlage.
2. When IN- is higher than the common mode voltage range and IN+ is within the common mode voltage
range, the output is low.
3. When IN+ is higher than the common mode voltage range and IN- is within the specified input voltage range,
the output is high
4. When IN- and IN+ are both outside the common mode voltage range, the output is low, regardless of which
input is greater.
Operating outside the common mode range causes changes in specifications such as propagation delay and
input bias current. Likewise, there is a recovery time when re-entering the common mode voltage range.
6.4.1.2 Fail-Safe Inputs
Fail-safe is defined as maintaining the same high input impedance when V+ is unpowered or within the
recommended operating ranges and is not damaged. The TLV192x inputs are fault tolerant up to 65V
independent of V+.
The fail-safe input voltage is any value between 0V and 65V from GND, even while V+ is zero or ramping up or
down. This feature avoids power sequencing issues as long as the input voltage range and supply voltage are
within the specified range.
The fail-safe inputs have snapback ESD protection from each pin to GND which allows these pins to exceed the
supply voltage (V+) up to 65V. If input voltages exceed 65V, an external clamp is required. Likewise, negative
voltages on the inputs are ESD clamped to GND and need to be limited to less than -0.2V.
If the inputs are to be connected to a low impedance source, such as a power supply or buffered reference
line, add a current-limiting resistor in series with the input to limit any transient currents the clamps conduct. The
current needs to be limited to 10mA or less. This series resistance can be part of any resistive input dividers or
networks.
6.4.1.3 Unused Inputs
If a channel is not used, DO NOT tie the inputs together. Due to the high equivalent bandwidth and low offset
voltage, tying the inputs directly together causes high frequency oscillations as the device triggers on it's own
internal wideband noise. Instead, the inputs are to be tied to any available voltage that resides within the
specified input voltage range and provides a minimum of 50mV differential voltage. For example, one input is
grounded and the other input connected to a reference voltage, or even (V+).
6.4.2 Open-Drain Output
The TLV192x features a open-drain (also commonly called open collector) sinking-only output stage enabling the
output logic levels to be pulled-up to an external voltage from 0 V up to 65V, independent of the comparator
supply voltage (V+). The open-drain output also allows logical OR'ing of multiple open drain outputs and logic
level translation. TI recommends setting the pull-up resistor current to less than 100 uA to optimize VOL logic
levels. Lower pull-up resistor values help increase the risetime, but at the expense of increasing VOL and higher
power dissipation. The risetime is dependent on the time constant of the total pull-up resistance and total load
capacitance. Large value pull-up resistors (>1 MΩ) create an exponential rising edge due to the output RC time
constant and increase the risetime.
Directly shorting the output to the pull-up voltage results in thermal runaway and eventual device destruction at
high (>65V) pull-up voltages. If output shorts are possible, a series current limitng resistor is recommended to
limit the power dissipation. Shorting the output to V+ can eventually destroy the device.
Unused open drain outputs can be left floating, or tied to the GND pin if floating pins are not desired.
www.ti.com
TLV1921, TLV1922
SNOSDG9 – DECEMBER 2024
Copyright © 2024 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TLV1921 TLV1922



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26


датащи скачать

Go To PDF Page


ссылки URL



Вашему бизинису помогли Аллдатащит?  [ DONATE ] 

Что такое Аллдатащит   |   реклама   |   контакт   |   Конфиденциальность   |   Ссылка на техническое описание    |   обмен ссыками   |   поиск по производителю
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com