CAT93C76 datasheet(2/13 Pages) CATALYST

2 / 13 page

CAT93C76 (Rev. A)

Doc. No. MD-1090 Rev. B

Characteristics subject to change without notice

ABSOLUTE MAXIMUM RATINGS

(1)

Parameters

Ratings

Units

Temperature Under Bias

–55 to +125

ºC

Storage Temperature

–65 to 150

ºC

Voltage on any Pin with Respect to Ground

(2)

-2.0 to +VCC +2.0

VCC with Respect to Ground

-2.0 to +7.0

Lead Soldering Temperature (10 seconds)

300

ºC

Output Short Circuit Current

(3)

100

RELIABILITY CHARACTERISTICS

(3)

Symbol

Parameter

Reference Test Method

Min

Units

NEND

(4)

Endurance

MIL-STD-883, Test Method 1033

1,000,000

Cycles/Byte

TDR

(4)

Data Retention

MIL-STD-883, Test Method 1008

100

Years

VZAP

(4)

ESD Susceptibility

MIL-STD-883, Test Method 3015

2000

ILTH

(4)(5)

Latch-Up

JEDEC Standard 17

100

D.C. OPERATING CHARACTERISTICS

VCC = +1.8V to +5.5V unless otherwise specified.

Symbol

Parameter

Test Conditions

Min

Typ

Max

Units

ICC1

Power Supply Current (Write)

fSK = 1MHz; VCC = 5.0V

ICC2

Power Supply Current (Read)

fSK = 1MHz; VCC = 5.0V

300

500

µA

ISB1

Power Supply Current

(Standby) (x8 Mode)

CS = 0V ORG = GND

µA

ISB2

Power Supply Current

(Standby) (x16Mode)

CS = 0V ORG = Float or VCC

(6)

µA

ILI

Input Leakage Current

VIN = 0V to VCC

(6)

µA

ILO

Output Leakage Current

VOUT = 0V to VCC, CS = 0V

(6)

µA

ILORG

ORG Pin Leakage Current

ORG = GND or ORG = VCC

µA

VIL1

Input Low Voltage

4.5V ≤ VCC ≤ 5.5V

-0.1

0.8

VIH1

Input High Voltage

4.5V ≤ VCC ≤ 5.5V

VCC + 1

VIL2

Input Low Voltage

1.8V ≤ VCC < 4.5V

VCC x 0.2

VIH2

Input High Voltage

1.8V ≤ VCC < 4.5V

VCC x 0.7

VCC + 1

VOL1

Output Low Voltage

4.5V ≤ VCC ≤ 5.5V; IOL = 2.1mA

0.4

VOH1

Output High Voltage

4.5V ≤ VCC ≤ 5.5V; IOH = -400µA

2.4

VOL2

Output Low Voltage

1.8V ≤ VCC < 4.5V; IOL = 100µA

0.1

VOH2

Output High Voltage

1.8V ≤ VCC < 4.5V; IOH = -100µA

VCC - 0.2

Notes:

(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings

only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this

specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.

(2) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20ns. Maximum DC

voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20ns.

(3) Output shorted for no more than one second.

(4) These parameters are tested initially and after a design or process change that affects the parameter.

(5) Latch-up protection is provided for stresses up to 100 mA on I/O pins from –1V to VCC +1V.

(6) 0µA is defined as less than 900nA.

CAT93C76 датащи(PDF) 2 Page - Catalyst Semiconductor

CAT93C76 датащи(HTML) 2 Page - Catalyst Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

датащи скачать

ссылки URL