| поискавой системы для электроныых деталей |
|
34702 датащи(PDF) 13 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
34702 датащи(HTML) 13 Page - Freescale Semiconductor, Inc |
|
13 / 38 page ![]() Analog Integrated Circuit Device Data Freescale Semiconductor 13 34702 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS BOOST REGULATOR Boost Regulator MOSFET Maximum ON Time (21) tON –24– µs Boost Regulator Control Loop Propagation Delay (21) tBST_PD –50– ns Boost Switching Node VBD Rise Time (21) IBST = 20 mA tB_RISE –5.0 ns Boost Switching Node VBD Fall Time (21) IBST = 20 mA tB_FALL –3.0 ns LINEAR REGULATOR (LDO) Fault Condition Time-Out tFAULT 8.0 10 12 ms Retry Timer Cycle tRet 80 100 120 ms Reset Monitor (RST) Monitoring LFB Pin Delay tD_RST_LFB 12–28 µs Monitoring INV Pin Delay tD_RST_INV 12–28 µs SCA, SCL PIN, I2C BUS (STANDARD) SCL Clock Frequency (21) fSCL – – 100 kHz Bus Free Time Between a STOP and a START Condition (21) tBUF 4.7 – – µs Hold Time (Repeated) START Condition (After this period, the first clock pulse is generated.) (21) tHD-STA 4.0 – – µs Low Period of the SCL Clock (21) tLOW 4.7 – – µs High Period of the SCL Clock (21) tHIGH 4.0 – – µs SDA Fall Time from VIH_MAX to VIL_MIN, Bus Capacitance 10 pF to 400 pF, 3.0 mA Sink Current (21), (23) tF – – 250 ns Setup Time for a Repeated START Condition (21) tSU-STA 4.7 – – µs Data Hold Time for I2C Bus Devices (21), (22) tHD-DAT 0.0 – – µs Data Setup Time (21) tSU-DAT 250 – – ns Setup Time for STOP Condition (21) tSU-STO 4.0 – – µs Capacitive Load for Each Bus Line (21) CB – – 400 pF Notes 21. Design information only. This parameter is not production tested. 22. The device provides an internal hold time of at least 300 ns for the SDA signal (refer to the V IH_MIN of the SCL signal) to bridge the undefined region of the falling edge of SCL. 23. VIH = High level voltage on I²C bus and VIL = Low level voltage on I²C bus Table 4. DYNAMIC ELECTRICAL CHARACTERISTICS (continued) Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using the typical application circuit (see Figures 33) unless otherwise noted. Characteristic Symbol Min Typ Max Unit |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |