RFM22 datasheet(33/150 Pages) HOPE

33 / 150 page

R F M 2 2

Tel: +86-755-82973805

Fax: +86-755-82973550

E-mail: sales@hoperf.com

http://www.hoperf.com

5. Internal Functional Blocks

This section provides an overview some of the key blocks of the internal radio architecture.

5.1. RX LNA

The input frequency range for the LNA is 240

–930 MHz. The LNA provides gain with a noise figure low enough to

suppress the noise of the following stages. The LNA has one step of gain control which is controlled by the analog

gain control (AGC) algorithm. The AGC algorithm adjusts the gain of the LNA and PGA so the receiver can handle

signal levels from sensitivity to +5 dBm with optimal performance.

5.2. RX I-Q Mixer

The output of the LNA is fed internally to the input of the receive mixer. The receive mixer is implemented as an I-Q

mixer that provides both I and Q channel outputs to the programmable gain amplifier. The mixer consists of two

double-balanced mixers whose RF inputs are driven in parallel, local oscillator (LO) inputs are driven in quadrature,

and separate I and Q Intermediate Frequency (IF) outputs drive the programmable gain amplifier. The receive LO

signal is supplied by an integrated VCO and PLL synthesizer operating between 240

–930 MHz. The necessary

quadrature LO signals are derived from the divider at the VCO output.

5.3. Programmable Gain Amplifier

The Programmable Gain Amplifier (PGA) provides the necessary gain to boost the signal level into the Dynamic

Range of the ADC. The PGA must also have enough gain switching to allow for large input signals to ensure a

linear RSSI range up to

–20 dBm. The PGA is designed to have steps of 3 dB which are controlled by the AGC

algorithm in the digital modem.

5.4. ADC

The amplified I&Q IF signals are digitized using an Analog-to-Digital Converter (ADC), which allows for low current

consumption and high dynamic range. The bandpass response of the ADC provides exceptional rejection of out of

band blockers.

5.5. Digital Modem

Using high-performance ADCs allows channel filtering, image rejection, and demodulation to be performed in the

digital domain, resulting in reduced area while increasing flexibility. The digital modem performs the following

functions:

Channel Selection Filter

TX Modulation

RX Demodulation

AGC

Preamble Detector

Invalid Preamble Detector

Radio Signal Strength Indicator (RSSI)

Automatic Frequency Compensation (AFC)

Packet Handling including EZMac

™ features

Cyclic Redundancy Check (CRC)

The digital Channel Filter and Demodulator are optimized for ultra low power consumption and are highly

configurable. Supported modulation types are GFSK, FSK, and OOK. The Channel Filter can be configured to

support a large choice of bandwidths ranging from 620 kHz down to 2.6 kHz. A large variety of data rates are

supported ranging from 1 up to 128 kbps. The AGC algorithm is implemented digitally using an advanced control

loop optimized for fast response time.

The configurable Preamble Detector is used to improve the reliability of the Sync-word detection. The Sync-word

detector is only enabled when a valid preamble is detected, significantly reducing the probability of false Sync-word

detection.

RFM22 датащи(PDF) 33 Page - HOPE Microelectronics CO., Ltd.

RFM22 датащи(HTML) 33 Page - HOPE Microelectronics CO., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL