PCF8584P datasheet(13/40 Pages) PHILIPS

13 / 40 page

1997 Oct 21

Philips Semiconductors

Product speciﬁcation

I2C-bus controller

PCF8584

6.8.2.7

‘Bus Busy’ bit. This is a read-only flag indicating when the

I2C-bus is in use. A zero indicates that the bus is busy, and

access is not possible. This bit is set/reset (logic 1/logic 0)

by STOP/START conditions.

6.9

Multi-master operation

To avoid conflict between data and repeated START and

STOP operations, multi-master systems have some

limitations:

• When powering up multiple PCF8584s in multi-master

systems, the possibility exists that one node may power

up slightly after another node has already begun an

I2C-bus transmission; the Bus Busy condition will thus

not have been detected. To avoid this condition, a delay

should be introduced in the initialization sequence of

each PCF8584 equal to the longest I2C-bus

transmission, see flowchart ‘PCF8584 initialization’

(Fig.5).

6.10

Reset

A LOW level pulse on the RESET (CLK must run) input

forces the I2C-bus controller into a well-defined state.

All flags in S1 are reset to logic 0, except the PIN flag and

the BB flag, which are set to logic 1. S0' and S3 are set

to 00H.

The RESET pin is also used for the STROBE output

signal. Both functions are separated on-chip by a digital

filter. The reset input signal has to be sufficiently long

(minimum 30 clock cycles) to pass through the filter.

The STROBE output signal is sufficiently short (8 clock

cycles) to be blocked by the filter. For more detailed

information on the strobe function see Section 6.12.

6.11

Comparison to the MAB8400 I2C-bus interface

The structure of the PCF8584 is similar to that of the

MAB8400 series of microcontrollers, but with a modified

control structure. Access to all I2C-bus control and status

registers is done via the parallel-bus port in conjunction

with register select input A0, and control bits ESO, ES1

and ES2.

6.11.1

DELETED FUNCTIONS

The following functions are not available in the PCF8584:

• Always selected (ALS flag)

• Access to the bit counter (BC0 to BC2)

• Full SCL frequency selection (2 bits instead of 5 bits)

• The non-acknowledge mode (ACK flag)

• Asymmetrical clock (ASC flag).

6.11.2

ADDED FUNCTIONS

The following functions either replace the deleted

functions or are completely new:

• Chip clock prescaler

• Assert acknowledge bit (ACK flag)

• Register selection bits (ES1 and ES2 flags)

• Additional status flags (BER, ‘bus error’)

• Automatic interface control between 80XX and

68000-type microcontrollers

• Programmable interrupt vector

• Strobe generator

• Bus monitor function

• Long-distance mode [non-I2C-bus mode (4-wire); only

for communication between parallel-bus processors

using the PCF8584 at each interface point].

6.12

Special function modes

6.12.1

STROBE

When the I2C-bus controller receives its own address (or

the ‘00H’ general call address) followed immediately by a

STOP condition (i.e. no further data transmitted after the

address), a strobe output signal is generated at the

RESET/STROBE pin (pin 19). The STROBE signal

consists of a monostable output pulse (active LOW),

8 clock cycles long (see Fig.9). It is generated after the

STOP condition is received, preceded by the correct slave

address. This output can be used as a bus access

controller for multi-master parallel-bus systems.

PCF8584P датащи(PDF) 13 Page - NXP Semiconductors

PCF8584P датащи(HTML) 13 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

датащи скачать

ссылки URL