 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
SS49 датащи(PDF) 1 Page - Honeywell Solid State Electronics Center |
|
|
|||||||||||||||||||||||||||||
SS49 датащи(HTML) 1 Page - Honeywell Solid State Electronics Center |
|
|
1 / 4 page  Installation Instructions for the ISSUE 2 SS49/SS19 Series Analog Position Sensors PK 88740 MICRO SWITCH Sensing and Control PERSONAL INJURY • DO NOT USE these products as safety or emergency stop devices, or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. SS49/SS19 ELECTRICAL CHARACTERISTICS Supply Voltage 4 to 10 VDC Supply Current 4 mA typ. Output Type Analog Sourcing Output Voltage @ 0 Gauss, 25 °C 1.75 to 2.25 V @ 5 V Sensitivity (measured between -400 and +400 gauss), mV/G Min. 0.60 Typ. 0.90 Max. 1.25 Operating Temperature -40 to +100 °C (-40 to 212°F) ABSOLUTE MAXIMUM RATINGS Supply Voltage (Vs) ± 12 VDC Output Current 20 mA Storage Temperature -55 to +150 °C (-67 to +302 °F) Magnetic Flux No limit. Circuit cannot be damaged by magnetic overdrive. Absolute maximum ratings are the extreme limits the device will withstand without damage to the device. However, the electrical and mechanical characteristics are not guaranteed as the maximum limits (above recommended operating conditions) are approached, nor will the device necessarily operate at absolute maximum ratings. SOLDERING/ASSEMBLY SS49 Support leads during any forming/shearing operation. Do not stress leads inside plastic case. Hand soldering - Use 60/40 rosin core solder, and a 399 °C (750°F) controlled temperature, 1/8” chisel tip soldering iron. Do not hold iron on terminals for more than four seconds. Lead temperature at package must not exceed 250 °C (482 °F). Wave soldering - Use Loncoflux 106A35 or equivalent. Set preheaters at 95 °C (200°F) for top (component side) of PC board just prior to entering wave. (This may be adjusted depending upon board thickness.) Set solder temperature at 252 °C to 260 °C max. (485°F to 500°F). Set conveyor speed to about 4.5 feet per minute (1,37 meter/min.), choosing a speed which gives full solder fillets and minimum bridging and icicles. Provide rigid support for the board. SS19/SS19T MICRO SWITCH recommends an infrared reflow process with peak temperatures not to exceed 190 - 200 °C (374 - 392°F) for 10 seconds maximum. Keep exposure to high temperatures minimal. CLEANING Clean appropriately in accordance with applicable safety procedures. MICRO SWITCH recommends manual cleaning. BLOCK DIAGRAM TRANSFER CHARACTERISTICS |
Аналогичный номер детали - SS49 |
|
Аналогичное описание - SS49 |
|
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
