PCD3360 datasheet(5/20 Pages) PHILIPS

5 / 20 page

1997 Jan 15

Philips Semiconductors

Product speciﬁcation

Programmable multi-tone telephone ringer

PCD3360

FUNCTIONAL DESCRIPTION (see Fig.1)

7.1

Supply pins (VDD and VSS)

If the supply current (VDD) drops below the standby voltage

(Vstb), the oscillator and most other functions are switched

off and the supply current is reduced to the standby current

(Istb). The automatic swell register retains its information

until VDD drops further to a value VAS at which reset

occurs.

7.2

Oscillator (OSC)

The 64 kHz oscillator is operated via an external resistor

and capacitor connected to pin OSC (see Fig.8).

The oscillator signal is divided by two to provide the 32 kHz

internal system clock.

7.3

Selection pin input circuit (see Fig.3)

Pins FDE, RR1, RR2, DM, IS1, IS2, TS1, TS2, FL and FH

are pulled down internally by a pull-down current IIH when

they are connected to VDD and by a pull-down resistance

RIL when they are connected to VSS. Thus when the pins

are open-circuit they are defined LOW. Therefore only a

single-contact switch is required to connect the pins to

VDD; yet the supply current is only marginally increased as

IIH is very small.

Fig.3 Input circuit of selection pins.

(1) Transistor resistance is RIL when switched on.

FDE

RR1

RR2

IS1

IS2

TS1

TS2

selection

pins

IIH

VSS

MGD709

PCD3360

(1)

7.4

Frequency discriminator circuit (FDE and FDI)

The frequency discriminator circuit prevents the ringer

being activated unintentionally by dial pulses, speech or

other invalid signals.

The circuit is enabled or disabled by input FDE. When FDE

is LOW and VDD >Vstb, the circuit is enabled and FDI acts

as the input for ringing frequency detection. When FDE is

HIGH, the circuit is disabled and FDI becomes the

enable/disable input for tone sequence generation.

When the circuit is enabled, it starts to produce output

ringing tones after one cycle of an appropriate input

frequency is detected at FDI. An input cycle is detected

when either 2 rising or 2 falling edges are received, and

this implies a delay of between 1 and 1.5 input cycles

before output ringing begins. The allowed input frequency

range is set by the states of pins FL and FH, as shown in

Table 2. Output ringing continues for as long as valid input

ringing frequency is detected.

FDI has a Schmitt-trigger action; the levels are set by an

external resistor R2 (see Fig.8) and an internal sink current

that is switched from 20

µA (typ.) for FDI = LOW to <0.1 µA

for FDI = HIGH. Excess current entering FDI via R2 is

absorbed by internal diodes clamped to VDD and VSS.

7.5

Selection of frequency discriminator limits

(FL and FH)

With the frequency discriminator enabled (VDD >Vstb and

FDE = LOW) the lower and upper limits of the input

frequency are set by the inputs FL and FH as shown by

Table 2.

Table 2

Selection of lower and upper frequency

discriminator limits (fOSC = 64 kHz)

FL INPUT

STATE

LOWER

LIMIT

FH INPUT

STATE

UPPER

LIMIT

LOW

20 Hz

LOW

60 Hz

HIGH

13.3 Hz

HIGH

30 Hz

PCD3360 датащи(PDF) 5 Page - NXP Semiconductors

PCD3360 датащи(HTML) 5 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

датащи скачать

ссылки URL