ADP151 datasheet(6/47 Pages) AD

6 / 47 page

Data Sheet

LT3046

analog.com

Rev 0

6 of 47

(TJ = -40°C to +125°C for the minimum and maximum values, TA = +25°C for the typical values, output capacitance

(COUT) = 4.7µF ceramic capacitor, and SET capacitance (CSET) = 4.7µF, unless otherwise noted.)

PARAMETER

SYMBOL

CONDITIONS/COMMENTS

MIN

TYP

MAX

UNITS

Thermal Shutdown

TJ rising

+165

°C

Hysteresis

Start-Up Time

VOUT(NOM) = 5V, IL = 200mA, CSET =

0.47µF, VIN = 6V, VPGFB = 6V

VOUT(NOM) = 5V, IL = 200mA, CSET =

4.7µF, VIN = 6V, VPGFB = 6V

550

VOUT(NOM) = 5V, IL = 200mA, CSET =

4.7µF, VIN = 6V, RPG1 = 50kΩ, RPG2 =

700kΩ (with fast startup to 90% of

VOUT)

Thermal Regulation

10ms pulse

-0.01

%/W

The EN/UV pin threshold must be met to ensure device operation.

The maximum TJ limits operating conditions. The regulated output-voltage specification does not apply for all

possible combinations of input voltage and output current, especially due to the internal current-limit foldback,

which starts to decrease current limit at VIN - VOUT > 11 V. If operating at the maximum output current, limit the

input-voltage range. If operating at the maximum input voltage, limit the output-current range.

OUTS ties directly to OUT.

Changes in ISET and VOS with VSET are tested at 0.2V, 0.75V, 1.3V, and 19V to ensure operation over the 0.2V to 19V

SET pin voltage range.

The dropout voltage is the minimum input-to-output differential voltage needed to maintain regulation at a

specified output current. The dropout voltage is measured when output is 1% out of regulation. This definition

results in a higher dropout voltage compared to hard dropout, which is measured when VIN = VOUT(NOMINAL). For

output voltages less than 1.7V, the dropout voltage is limited by the minimum input-voltage specification. See

Figure 18 for the dropout voltage as a function of the output current and for temperature, see Figure 19, which

was measured in a typical application circuit.

The GND pin current is tested with VIN = VOUT(NOMINAL) and a current source load. Therefore, the LT3046 is tested

while operating in dropout, which is the worst-case GND pin current. The GND pin current decreases at higher

input voltages. Note that the GND pin current does not include the SET pin or the ILIM pin current; however,

quiescent current does include the SET and ILIM pins.

Adding a capacitor across the SET pin resistor decreases the output voltage noise. Adding this capacitor

bypasses the thermal noise of the resistor on the SET pin as well as the noise of the reference current. The

output noise then equals the error-amplifier noise. Use of a SET pin bypass capacitor also increases the start-up

time.

The internal back-up current-limit circuitry incorporates foldback protection that decreases current limit for VIN

- VOUT > 11 V. Some level of output current is provided at all VIN - VOUT differential voltages. See Figure 32 for the

current limit as a function of VIN - VOUT.

ADP151 датащи(PDF) 6 Page - Analog Devices

ADP151 датащи(HTML) 6 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

датащи скачать

ссылки URL