AM29LV010B datasheet(13/36 Pages) AMD

13 / 36 page

October 11, 2006 22140D6

Am29LV010B

D A TA SH EE T

Power-Up Write Inhibit

If WE# = CE# = VIL and OE# = VIH during power up, the

device does not accept commands on the rising edge

of WE#. The internal state machine is automatically

reset to reading array data on power-up.

COMMAND DEFINITIONS

Writing specific address and data commands or

sequences into the command register initiates device

operations. Table 4 defines the valid register command

sequences. Writing incorrect address and data

values or writing them in the improper sequence

resets the device to reading array data.

All addresses are latched on the falling edge of WE# or

CE#, whichever happens later. All data is latched on

the rising edge of WE# or CE#, whichever happens

first. Refer to the appropriate timing diagrams in the

“AC Characteristics” section.

Reading Array Data

The device is automatically set to reading array data

after device power-up. No commands are required to

retrieve data. The device is also ready to read array

data after completing an Embedded Program or

Embedded Erase algorithm.

After the device accepts an Erase Suspend command,

the device enters the Erase Suspend mode. The

system can read array data using the standard read

timings, except that if it reads at an address within

erase-suspended sectors, the device outputs status

data. After completing a programming operation in the

Erase Suspend mode, the system may once again

read array data with the same exception. See “Erase

Suspend/Erase Resume Commands” for more infor-

mation on this mode.

The system must issue the reset command to re-

enable the device for reading array data if DQ5 goes

high, or while in the autoselect mode. See the “Reset

Command” section, next.

See also “Requirements for Reading Array Data” in the

“Device Bus Operations” section for more information.

The Read Operations table provides the read parame-

ters, and Figure 11 shows the timing diagram.

Reset Command

Writing the reset command to the device resets the

device to reading array data. Address bits are don’t

care for this command.

The reset command may be written between the

sequence cycles in an erase command sequence

before erasing begins. This resets the device to reading

array data. Once erasure begins, however, the device

ignores reset commands until the operation is

complete.

The reset command may be written between the

sequence cycles in a program command sequence

before programming begins. This resets the device to

reading array data (also applies to programming in

Erase Suspend mode). Once programming begins,

however, the device ignores reset commands until the

operation is complete.

The reset command may be written between the

sequence cycles in an autoselect command sequence.

Once in the autoselect mode, the reset command must

be written to return to reading array data (also applies

to autoselect during Erase Suspend).

If DQ5 goes high during a program or erase operation,

writing the reset command returns the device to

reading array data (also applies dur ing Erase

Suspend).

Autoselect Command Sequence

The autoselect command sequence allows the host

system to access the manufacturer and devices codes,

and determine whether or not a sector is protected.

Table 4 shows the address and data requirements. This

method is an alternative to that shown in Table 3, which

is intended for PROM programmers and requires VID

on address bit A9.

The autoselect command sequence is initiated by

writing two unlock cycles, followed by the autoselect

command. The device then enters the autoselect

mode, and the system may read at any address any

number of times, without initiating another command

sequence. A read cycle at address XX00h retrieves the

manufacturer code. A read cycle at address XX01h

returns the device code. A read cycle containing a

sector address (SA) and the address 02h returns 01h if

that sector is protected, or 00h if it is unprotected. Refer

to Table 2 for the valid sector addresses.

The system must write the reset command to exit the

autoselect mode and return to reading array data.

Byte Program Command Sequence

The device programs one byte of data for each program

operation. The command sequence requires four bus

cycles, and is initiated by writing two unlock write

cycles, followed by the program set-up command. The

program address and data are written next, which in

turn initiate the Embedded Program algorithm. The

system is not required to provide further controls or tim-

ings. The device automatically provides internally

AM29LV010B датащи(PDF) 13 Page - Advanced Micro Devices

AM29LV010B датащи(HTML) 13 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

датащи скачать

ссылки URL