2

FN3393.8

June 2, 2006

Absolute Maximum Ratings

Thermal Information

Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . .36V

DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . .

±V

SUPPLY

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V

Output Current (Note 4) . . . . . . . . . . . . . . . . . Short Circuit Protected

ESD Rating (Note 3)

Human Body Model (Per MIL-STD-883 Method 3015.7). . . 2000V

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C

Supply Voltage Range (Typical). . . . . . . . . . . . . . . . .

±4.5V to ±15V

Thermal Resistance (Typical, Note 2)

θ

PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .

130

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160

Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . . 175°C

Maximum Junction Temperature (Plastic Package, Note 1) . . 150°C

Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C

(SOIC - Lead Tips Only)

*Pb-free PDIPs can be used for through hole wave solder process-

ing only. They are not intended for use in Reflow solder processing

applications.

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175°C for die, and below 150°C

for plastic packages. See Application Information section for safe operating area information.

2.

3. The non-inverting input of unused amplifiers must be connected to GND.

4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle)

output current should not exceed 15mA for maximum reliability.

PARAMETER

TEST CONDITIONS

(NOTE 9)

TEST

LEVEL

TEMP.

(°C)

MIN

TYP

MAX

UNITS

INPUT CHARACTERISTICS

25

-

0.8

3

mV

AFull

-

-

5

mV

A

Full

-

1.2

3.5

mV

Average Input Offset Voltage Drift

B

Full

-

5

-

µV/°C

Note 5

A

25

53

-

-

dB

A

Full

50

-

-

dB

±3.5V ≤ V

A

25

60

-

-

dB

AFull

55

-

-

dB

Input Common Mode Range

Note 5

A

Full

±2.5

-

-

V

Non-Inverting Input (+IN) Current

A

25

-

3

8

µA

AFull

-

-

20

µA

+IN Common Mode Rejection

Note 5

A

25

-

-

0.15

µA/V

AFull

-

-

0.5

µA/V

+IN Power Supply Rejection

±3.5V ≤ V

A

25

-

-

0.1

µA/V

AFull

-

-

0.3

µA/V

Inverting Input (-IN) Current

A

25, 85

-

4

12

µA

A-40

-

10

30

µA

Delta -IN BIAS Current Between Channels

A

25, 85

-

6

15

µA

A-40

-

10

30

µA

1

HA5023