| поискавой системы для электроныых деталей |
|
MPC5565 датащи(PDF) 12 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MPC5565 датащи(HTML) 12 Page - Freescale Semiconductor, Inc |
|
12 / 48 page ![]() MPC5565 Microcontroller Data Sheet, Rev. 0 Preliminary—Subject to Change Without Notice Electrical Characteristics Freescale Semiconductor 12 the internal 3.3-V POR or the RESET power POR must be depended on to hold the device in reset. Since they may negate as low as 2.0 V, it is necessary for VDD to be within spec before the 3.3-V POR and the RESET POR negate. Figure 2. Power Up Sequence if VRC33 Grounded 3.7.2 Power Down Sequence (If VRC33 Grounded) In this case, the only requirement is that if VDD falls below its operating range, VDDSYN or the RESET power must fall below 2.0 V before VDD is allowed to rise back into its operating range. This ensures that digital 1.5-V logic that is only reset by ORed_POR, which may have been affected by the 1.5V supply falling below spec, is reset properly. 3.7.3 Input Value of Pins During POR Dependent on VDD33 In order to avoid accidentally selecting the bypass clock because PLLCFG[0:1] and RSTCFG are not treated as 1s when POR negates, VDD33 must not lag VDDSYN and the RESET pin power (VDDEH6) when powering the device by more than the VDD33 lag specification in Table 6. VDD33 individually can lag either VDDSYN or the RESET pin power (VDDEH6) by more than the VDD33 lag specification. VDD33 can lag one of the VDDSYN or VDDEH6 supplies, but cannot lag both by more than the VDD33 lag specification. This VDD33 lag specification only applies during power up. VDD33 has no lead or lag requirements when powering down. 3.8 DC Electrical Specifications Table 9. DC Electrical Specifications Num Characteristic Symbol Min Max Unit 1 Core Supply Voltage (average DC RMS voltage) VDD 1.35 1.65 V 2 I/O Supply Voltage (Fast I/O) VDDE 1.62 3.6 V 3 I/O Supply Voltage (Slow/Medium I/O) VDDEH 3.0 5.25 V 4 3.3V I/O Buffer Voltage VDD33 3.0 3.6 V 5 Voltage Regulator Control Input Voltage VRC33 3.0 3.6 V VDDSYN and RESET Power VDD 2.0V 1.35V VDD must reach 1.35V before VDDSYN and the RESET power reach 2.0V |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |