| поискавой системы для электроныых деталей |
|
USB2524 датащи(PDF) 13 Page - SMSC Corporation |
|
|
|||||||||||||||||||||||||||||
USB2524 датащи(HTML) 13 Page - SMSC Corporation |
|
13 / 57 page ![]() USB MultiSwitchTM Hub Datasheet SMSC USB2524 13 Revision 1.2 (07-17-06) DATASHEET Chapter 5 Switching Hub Pin Descriptions Table 5.1 Switching Hub Pin Descriptions NAME SYMBOL TYPE FUNCTION UPSTREAM USB2.0 INTERFACE USB Bus Data USBUP_DP[2:1] USBUP_DM[2:1] IO-U These pins connect to the upstream USB bus data signals. Detect Upstream VBUS Power VBUS_DET[2:1] I/O Detects state of Upstream VBUS power. The SMSC Hub monitors VBUS_DET to determine when to assert the internal D+ pull-up resistor (signalling a connect event). When designing a detachable hub, this pin must be connected to the VBUS power pin of the USB port that is upstream of the hub. (Use of a weak pull-down resistor is recommended.) For self-powered applications with a permanently attached host, this pin must be pulled-up to either 3.3V or 5.0V (typically VDD33). 4-PORT USB2.0 HUB INTERFACE High-Speed USB Data USBDN_DP[4:1] USBDN_DM[4:1] IO-U These pins connect to the downstream USB peripheral devices attached to the Hub’s ports. USB Power Enable PRTPWR[4:1] O Enables power to USB peripheral devices (downstream). The active signal level of the PRTPWR[4] pin is determined by the Power Polarity Strapping function of the PRTPWR_POL pin. Port 4:3 Green LED & Port Disable strapping option LED_A[4:3]_N/ PRT_DIS[1:0] I/O12 Green indicator LED for ports 4 and 3. Will be active low when LED support is enabled via EEPROM or SMBus. If the hub is configured by the internal default configuration, these pins will be sampled at RESET_N negation to determine if ports [4:2] will be permanently disabled. Also, the active state of the LED's will be determined as follows: PRT_DIS[1:0] = '00', All ports are enabled, LED_A4_N is active high, LED_A3_N is active high. PRT_DIS[1:0] = '01', Port 4 is disabled, LED_A4_N is active high, LED_A3_N is active low. PRT_DIS[1:0] = '10', Ports 4 & 3 are disabled, LED_A4_N is active low, LED_A3_N is active high. PRT_DIS[1:0] = '11', Ports 4, 3 & 2 are disabled, LED_A4_N is active low, LED_A3_N is active low. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |