www.ittcannon.com

205

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

MIL-C-5015 Firewall Connectors

MS-K

Recommended Procedures

CONTACT RETAINING CLIP

FRONT

INSULATOR

CONTACT

(CRIMP-ON

TERMINALS)

REAR

INSULATOR

INSERT

RETAINING

RING

INSERT

RETAINING

WASHER

STEEL ENDBELL

FIGURE 1

STEEL BARREL

Contact Size

16-Pin

8S-36

16 Pin*

8S-36

16 Socket

8S-16S

16 Socket

12-36

16 Socket*

12-36

12 Pin

12 Socket

8 Pin

8 Socket

4 Pin

4 Socket

0 Pin

0 Socket

330-0187-000

030-1154-000

031-0497-000

031-0498-000

031-0728-000

330-0188-000

031-0499-000

330-0189-000

031-0500-000

330-0190-000

031-0501-000

330-0191-000

031-0502-000

16-Pin

8S-36

16 Pin*

8S-36

16 Socket

8S-16S

16 Socket

12-36

16 Socket*

12-36

12 Pin

12 Socket

8 Pin

8 Socket

4 Pin

4 Socket

0 Pin

0 Socket

320-0002-000

320-0001-000

320-0013-000

320-0005-000

320-0008-000

320-0009-000

320-0007-000

320-0010-000

320-0014-000

320-0011-000

320-0006-000

320-0012-000

320-0015-000

16-18-20

16-18-20

16-18-20

16-18-20

16-18-20

12-14

12-14

8

8

4

4

0

0

MS22520/1-01

MS3191-1

MS22520/1-01

MS3191-1

MS22520/1-01

MS3191-1

MS22520/1-01

MS3191-1

MS22520/1-01

MS3191-1

MS22520/1-01

MS3191-1

MS22520/1-01

MS3191-1

CBT600B or

CBT600

CBT600B or

CBT600

CBT600B or

CBT600

CBT600B or

CBT600

CBT600B

CBT600B

TH119 Turret

L16-3191-8

TH119 Turret

L16-3191-8

TH119 Turret

L16-3191-8

TH119 Turret

L16-3191-7

TH119 Turret

L16-3191-7

TH119 Turret

L12-3191-4

TH119 Turret

L12-3191-4

CCHP8

CCHP8

CCHP4

CCHP4

CCHP0-6

CCHP0-6

-

-

-

-

-

-

-

CCH8-1

CCH8-1

CCH4-1

CCH4-1

CCH0-1

CCH0-1

Part Number

Wire Accom.

Crimp Tool

Locator

Crimp Head†

Contact Size

Kit Part Number

MS-K Contacts and Crimp Tools can be ordered separately

MS-K Contacts Assembly Kit

With Contact and Retaining Ring

*NOTE: For MS-K Assembly it is not neccessary to remove the ceramic retaining ring used on sizes 16

and 12 contacts for MS-K providing that the crimp tool M22520/1-01 is used with the TH119 turret.

However, the formica ring must be removed if using the crimp tools listed below.

*These contacts must be used when ordering contact arrangments 24-28 pin or socket, 28-21 pin or socket, and 20-27 socket only.

†Crimp heads are only applicable for contact sizes 8, 4, and 0.

When using the MS3191-1 (or CCT-1612) crimp tool with property locator, both the ceramic or formica

retaining ring for sizes 16 and 12 contacts must be removed. For sizes 8, 4, and 0 contacts, the

ceramic or formica retaining rings must be removed before crimping.

STEEL COUPLING NUT

1. Remove Formica retaining ring (or the ce-

ramic retaining ring) from contact (Figure 1).

2. Crimp contact to wire.

3. Slip endbell (or junction shell), retaining ring,

and washer over wire bundle.

4. Push contact thru rear insulator. (Contact

should extend sufficiently to accomplish

Step 5.)

5.

Attach Formica retaining ring onto the con-

tact (see Figure 1).

6.

Seat each contact securely in rear insulator.

7.

Assemble front insulator on engaging end of

contact.

8.

Slide insulator assembly into hardware.

9.

Slide washer and insulator retaining ring into

place, making sure that insulator retaining is

fully seated in groove.

10. Slide endbell or junction shell down wire

bundle and attach to shell (or barrel).

*

Assembly Instructions

Contacts, Crimp Tools, Contact Kit Part Numbers