AM29SL400DB120WAF datasheet(20/41 Pages) SPANSION

20 / 41 page

Am29SL400D

Rev. A Amend. +1 April 13, 2005

ADV ANCE

I N FO RMAT I O N

Write Operation Status

The device provides several bits to determine the status

of a write operation: DQ2, DQ3, DQ5, DQ6, DQ7, and

RY/BY#. Table 6 on page 21 and the following subsec-

tions describe the functions of these bits. DQ7, RY/BY#,

and DQ6 each offer a method for determining whether

a program or erase operation is complete or in progress.

These three bits are discussed first.

DQ7: Data# Polling

The Data# Polling bit, DQ7, indicates to the host system

whether an Embedded Algorithm is in progress or com-

pleted, or whether the device is in Erase Suspend.

Data# Polling is valid after the rising edge of the final

WE # pu ls e in t h e pro g ra m or erase c o mm a n d

sequence.

During the Embedded Program algorithm, the device

outputs on DQ7 the complement of the datum pro-

grammed to DQ7. This DQ7 status also applies to pro-

gramming during Erase Suspend. When the Embedded

Program algorithm is complete, the device outputs the

datum programmed to DQ7. The system must provide

the program address to read valid status information on

DQ7. If a program address falls within a protected

sector, Data# Polling on DQ7 is active for approximately

1 µs, then the device returns to reading array data.

During the Embedded Erase algorithm, Data# Polling

produces a “0” on DQ7. When the Embedded Erase

algorithm is complete, or if the device enters the Erase

Suspend mode, Data# Polling produces a “1” on DQ7.

This is analogous to the complement/true datum output

described for the Embedded Program algorithm: the

erase function changes all the bits in a sector to “1”;

prior to this, the device outputs the “complement,” or “0.”

The system must provide an address within any of the

sectors selected for erasure to read valid status infor-

mation on DQ7.

After an erase command sequence is written, if all

sectors selected for erasing are protected, Data#

Polling on DQ7 is active for approximately 100 µs, then

the device returns to reading array data. If not all

selected sectors are protected, the Embedded Erase

algorithm erases the unprotected sectors, and ignores

the selected sectors that are protected.

When the system detects DQ7 has changed from the

complement to true data, it can read valid data at

DQ7–DQ0 on the

following read cycles. This is because

DQ7 may change asynchronously with DQ0–DQ6 while

Output Enable (OE#) is asserted low. Figure 19, on

page 32, Data# Polling Timings (During Embedded

Algorithms), illustrates this.

Table 6 on page 21 shows the outputs for Data# Polling

on DQ7. Figure 5 shows the Data# Polling algorithm.

RY/BY#: Ready/Busy#

The RY/BY# is a dedicated, open-drain output pin that

indicates whether an Embedded Algorithm is in

progress or complete. The RY/BY# status is valid after

the rising edge of the final WE# pulse in the command

sequence. Since RY/BY# is an open-drain output,

several RY/BY# pins can be tied together in parallel with

a pull-up resistor to VCC.

DQ7 = Data?

Yes

DQ5 = 1?

Yes

FAIL

PASS

Read DQ7–DQ0

Addr = VA

Read DQ7–DQ0

Addr = VA

DQ7 = Data?

START

Notes:

1. VA = Valid address for programming. During a sector

erase operation, a valid address is an address within any

sector selected for erasure. During chip erase, a valid

address is any non-protected sector address.

2. DQ7 should be rechecked even if DQ5 = “1” because

DQ7 may change simultaneously with DQ5.

Figure 5.

Data# Polling Algorithm

AM29SL400DB120WAF датащи(PDF) 20 Page - SPANSION

AM29SL400DB120WAF датащи(HTML) 20 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

датащи скачать

ссылки URL