ICS1893 datasheet(27/153 Pages) RENESAS

27 / 153 page

Chapter 6

Interface Overviews

ICS1893 Rev C 6/6/00

June, 2000

ICS1893 - Release

6.2

100M Symbol Interface

The 100M Symbol Interface has a primary objective of supporting 100Base-TX repeater applications for

which the repeater requires only recovered parallel data and for which the repeater provides all the

necessary framing and control functions.

When the ICS1893 MAC/Repeater Interface is configured for 100M Symbol operations, the PHY and the

MAC/repeater exchange unframed 5-bit, parallel symbols at a 25-MHz clock rate.

The configuration functions of the ICS1893 determine the operation of its MAC/Repeater Interface. The

configuration functions are controlled by either input pins (in which case, the HW/SW pin is logic zero to

select the hardware mode) or Management Register bits (in which case, the HW/SW pin is logic one to

select the software mode).

• In hardware mode, the ICS1893 enables the 100M Symbol Interface when both of the following are true:

– Its MII/SI input pin is sampled as a logic one (that is, the selection is for the Symbol Interface).

– Its 10/100SEL input pin is sampled as a logic one (that is, the selection is for 100M operations).

• In software mode, the ICS1893 enables the 100M Symbol Interface when both the following are true:

– Its MII/SI input pin is sampled as a logic one (that is, the selection is for the Symbol Interface).

– Its Control Register Data Rate bit (bit 0.13) is set to logic one (that is, the selection is for selecting

100M operations)

The 100M Symbol Interface bypasses the ICS1893’s PCS and provides a direct, unscrambled, unframed,

5-bit interface between the MAC/repeater and the PMA sublayer. A benefit of bypassing the PCS is a

reduction in the latency through the PHY. That is, when the ICS1893’s MAC/Repeater Interface is

configured as a 100M Symbol Interface, the bit delays through the PHY are smaller than the standard MII

Data Interface can allow. The ICS1893 provides this 100M Symbol Interface primarily for Repeater

applications, for which latency is a critical performance parameter.

In addition to the exchange of symbol data, an ICS1893 configured for 100M Symbol mode provides

ISO/IEC-compliant control signals (such as CRS) to the MAC/repeater. The ICS1893’s CRS signal

provides a fast look-ahead, which can benefit a repeater application.

In the 100M Symbol Interface mode, the ICS1893 continues to assert the CRS signal using its PCS logic.

This action does not affect the bit delay or latency because the PCS CRS logic examines the bits received

from the PMA sublayer serially. In fact, because the PCS CRS does not wait for a nibble or symbol to be

constructed, the PCS CRS is available in advance of the symbol generation. Therefore, by using the PCS

CRS generation logic, the ICS1893 can provide an ‘early’indication of a Carrier Detect to the

MAC/repeater.

The 100M Symbol Interface consists of the following fourteen signals:

• SCRS

• SD

• SRCLK

• SRD[4:0]

• STCLK

• STD[4:0]

When the ICS1893 MAC/Repeater Interface is configured for 100M Symbol operations, its default MII pin

names and their associated functions are redefined. For more information, see Section 9.3.4.2,

“MAC/Repeater Interface Pins for 100M Symbol Interface”.

ICS1893 датащи(PDF) 27 Page - Renesas Technology Corp

ICS1893 датащи(HTML) 27 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL