www.gminternational.com

D5038

I.S. SIL3 Line-Fault Transp. Switch/Prox. Repeater

Intrinsically Safe Isolators > Digital Input

ORDERING INFORMATION

Ordering codes

D5038xy

x: S → 1 channel; D → 2 channels; X → duplicator

y: A → RL = 2.2 kΩ, RH = 14.3 kΩ; B → RL = 476 Ω, RH = 1.38 kΩ

C → RL = 5 kΩ, RH = 15 kΩ; D → RL = 0 Ω, RH = 33.2 kΩ

Accessories

Bus Connector JDFT049, Bus Mounting Kit OPT5096.

TECHNICAL DATA

SIL 3 / SC 3

Input from Zone 0/Div. 1

Installation in Zone 2/Div. 2

Field open and short circuit detection

Field fault universal mirroring to PLC DI

Line monitoring transparency

In-field programmability by DIP Switch

Three port isolation, Input/Output/Supply

High Density, two channels per unit

The Switch/Proximity Detector Repeater D5038 is a module suitable

for applications requiring SIL 3 level in safety related systems for

high risk industries. The unit can be configured for switches or

proximity detectors, located in Hazardous Area, and repeats the input

state to the output in Safe Area. The output port can assume two

different impedance values (RL or RH) or it can open completely.

The module output repeats the input state according to the following

correspondence: low input state -> RL, high input state -> RH.

Alternatively, the output can be configured to invert the input state. In

both cases, the output opens if any fault (open or short circuit) occurs

at the corresponding input.

FEATURES

Supply

24 Vdc nom (18 to 30 Vdc), reverse polarity protected.

Current consumption: 30 mA (D5038D), 25 mA (D5038X), 15 mA

(D5038S), @ 24 Vdc, typical.

Power dissipation: 1.0 W (D5038D), 1.0 W (D5038X), 0.4 W (D5038S),

@ 24 Vdc, typical.

Input

Input switching current levels: ON ≥ 2.1 mA, OFF ≤ 1.2 mA.

Open fault: current ≤ 0.05 mA.

Short fault: resistance ≤ 100 Ω.

No fault: current ≥ 0.35 mA and resistance ≥ 360 Ω.

Input equivalent source: 8 V 1 kΩ typical (8 V no load, 8 mA short).

Output

Voltage free SPST solid-state relays, with series (RL) and parallel (RH-RL)

resistances, ±5% tolerance.

Fault impedance: > 1 MΩ.

Max voltage: 30 Vdc.

Max current: 15 mA.

Response time: 500 µs.

Frequency response: 1 kHz maximum.

Isolation

I.S. In/Out 1.5 kV; I.S. In/Supply 1.5 kV; I.S. In/ I.S In 500 V; Out/Supply

500 V; Out/Out 500 V.

Environmental conditions

Operating temperature: temperature limits –40 to +70 °C.

Storage temperature: temperature limits –45 to +80 °C.

Safety description

Associated apparatus and non-sparking electrical equipment.

Uo = 10.5 V, Io = 22 mA, Po = 56 mW at terminals 7-8, 9-10.

Um = 250 Vrms or Vdc, -40 °C ≤ Ta ≤ 70 °C.

Mounting

DIN-Rail 35 mm, with or without Power Bus or on custom Term. Board.

Weight: about 135 g (D5038D and D5038X), 120 g (D5038S).

Connection: by polarized plug-in disconnect screw terminal blocks to

accommodate terminations up to 2.5 mm² (13 AWG).

Dimensions: Width 12.5 mm, Depth 123 mm, Height 120 mm.

OVERALL DIMENSIONS

Functional Safety Management Certification:

GM International is certified to conform to IEC61508:2010 part 1 clauses 5-6 for safety related systems up to and included SIL3. In addition, GM International products have been granted I.S.

certificates from the most credited Notified Bodies in the world.

Data specified in this document are merely descriptive of the products and should be integrated with relevant technical specifications. Our products are in constant development and the information

presented herein refers to the time of document issue. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not

release the user from the obligation of own judgment and verification. Terms & Conditions can be found at our website. For more information refer to istruction manual.

DTS0827-8

© G.M. International s.r.l.

Page 1/2