HIP4080

FN3178 Rev 11.00

Page 4 of 21

February, 2003

Absolute Maximum Ratings

Thermal Information

Supply Voltage, VDD and VCC . . . . . . . . . . . . . . . . . . . -0.3V to 16V

Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V

Voltage on AHS, BHS . . . -6.0V (Transient) to 80V (25oC to 125oC)

Voltage on AHS, BHS . . . -6.0V (Transient) to 70V (-55oC to 125oC

Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient)

Voltage on AHB, BHBVAHS, BHS -0.3V to VAHS, BHS +16VVoltage on

Voltage on ALO, BLO . . . . . . . . . . . .VALS, BLS -0.3V to VCC +0.3V

Voltage on AHO, BHO . . . . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V

Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA

Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns

All Voltages relative to pin 4, VSS, unless otherwise specified.

Thermal Resistance (Typical, Note 1). . . . . . . . . . . . . . .

JA (oC/W)

SOIC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Maximum Power Dissipation at 85oC

SOIC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470mW

DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530mW

Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to 150oC

Operating Max. Junction Temperature . . . . . . . . . . . . . . . . . . 125oC

Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . . 300oC

(SOIC - Lead Tips Only)

Operating Conditions

Supply Voltage, VDD and VCC . . . . . . . . . . . . . . . . . . . +8V to +15V

Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V

Voltage on AHB, BHB . . . . . . . VAHS, BHS +5V to VAHS, BHS +15V

Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . -500

A to -50A

Operating Ambient Temperature Range . . . . . . . . . . -40oC to 85oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTE:

1.

JA is measured with the component mounted on an evaluation PC board in free air.

Electrical Specifications

VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100K, and

TA =25oC, Unless Otherwise Specified

PARAMETERS

SYMBOL

TEST CONDITIONS

TJ = 25oC

TJ = - 40oC

TO 125oC

UNITS

MIN

TYP

MAX

MIN

MAX

SUPPLY CURRENTS AND CHARGE PUMPS

VDD Quiescent Current

IDD

IN- = 2.5V, Other Inputs = 0V

8

10.5

13

7

14

mA

VDD Operating Current

IDDO

Outputs switching f = 500kHz

9

11

14

8

15

mA

VCC Quiescent Current

ICC

IN- = 2.5V, Other Inputs = 0V,

IALO = IBLO = 0

-25

80-

100

A

VCC Operating Current

ICCO

f = 500kHz, No Load

1

1.5

2.0

0.8

3

mA

AHB, BHB Quiescent Current -

Qpump Output Current

IAHB, IBHB IN- = 2.5V, Other Inputs = 0V, IAHO =

IBHO = 0, VDD = VCC = VAHB =

VBHB = 10V

-50

-30

-15

-60

-10

A

AHB, BHB Operating Current

IAHBO,

IBHBO

f = 500kHz, No Load

0.5

0.9

1.3

0.4

1.7

mA

AHS, BHS, AHB, BHB Leakage Current

IHLK

VAHS = VBHS = VAHB = VBHB = 95V

-

0.02

1.0

-

10

A

AHB-AHS, BHB-BHS Qpump

Output Voltage

VAHB -

VAHS

VBHB -

VBHS

IAHB = IAHB = 0, No Load

11.5

12.6

14.0

10.5

14.5

V

INPUT COMPARATOR PINS: IN+, IN-, OUT

Offset Voltage

VOS

Over Common Mode Voltage Range

-10

0

+10

-15

+15

mV

Input Bias Current

IIB

0

0.5

204

A

Input Offset Current

IOS

-1

0

+1

-2

+2

A

Input Common Mode Voltage Range

CMVR

1

-

VDD

-1.5

1VDD

-1.5

V

Voltage Gain

AVOL

10

25

-

10

-

V/mV