2

Absolute Maximum Ratings

Thermal Information

Voltage Between V+ and V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11V

DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8V

Output Current (Note 2) . . . . . . . . . . . . . . . . .Short Circuit Protected

30mA Continuous

60mA

≤ 50% Duty Cycle

ESD Rating

Human Body Model (Per MIL-STD-883 Method 3015.7) . . . 600V

Operating Conditions

Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC

Thermal Resistance (Typical, Note 1)

θJA (oC/W)

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

105

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160

Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC

Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

(SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

1.

θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

2. Output is short circuit protected to ground. Brief short circuits to ground will not degrade reliability, however continuous (100% duty cycle) output

current must not exceed 30mA for maximum reliability.

Electrical Specifications VSUPPLY = ±5V, AV = +1, RF = 560Ω, RL = 100Ω, Unless Otherwise Specified

PARAMETER

TEST CONDITIONS

(NOTE 3)

TEST

LEVEL

TEMP.

(oC)

MIN

TYP

MAX

UNITS

INPUT CHARACTERISTICS

Input Offset Voltage

A

25

-

2

5

mV

AFull

-

3

8

mV

Average Input Offset Voltage Drift

B

Full

-

1

10

μV/ oC

Input Offset Voltage

Common-Mode Rejection Ratio

ΔVCM = ±1.8V

A

25

45

48

-

dB

ΔVCM = ±1.8V

A

85

43

46

-

dB

ΔVCM = ±1.2V

A

-40

43

46

-

dB

Input Offset Voltage

Power Supply Rejection Ratio

ΔVPS = ±1.8V

A

25

48

52

-

dB

ΔVPS = ±1.8V

A

85

46

50

-

dB

ΔVPS = ±1.2V

A

-40

46

50

-

dB

Non-Inverting Input Bias Current

A

25

-

6

15

μA

A

Full

-

10

25

μA

Non-Inverting Input Bias Current Drift

B

Full

-

5

60

nA/oC

Non-Inverting Input Bias Current

Power Supply Sensitivity

ΔVPS = ±1.8V

A

25

-

0.5

1

μA/V

ΔVPS = ±1.8V

A

85

-

0.8

3

μA/V

ΔVPS = ±1.2V

A

-40

-

0.8

3

μA/V

Non-Inverting Input Resistance

ΔVCM = ±1.8V

A

25

0.8

2

-

M

Ω

ΔVCM = ±1.8V

A

85

0.5

1.3

-

M

Ω

ΔVCM = ±1.2V

A

-40

0.5

1.3

-

M

Ω

Inverting Input Bias Current

A

25

-

2

8.5

μA

AFull

-

5

15

μA

Inverting Input Bias Current Drift

B

Full

-

60

200

nA/oC

Inverting Input Bias Current

Common-Mode Sensitivity

ΔVCM = ±1.8V

A

25

-

3

6

μA/V

ΔVCM = ±1.8V

A

85

-

4

8

μA/ V

ΔVCM = ±1.2V

A

-40

-

4

8

μA/V

HFA1205