87LPC769 datasheet(21/61 Pages) PHILIPS

21 / 61 page

Philips Semiconductors

Preliminary specification

87LPC769

Low power, low price, low pin count (20 pin)

microcontroller with 4 kB OTP 8-bit A/D, and DAC

2001 Jan 11

BIT

SYMBOL

FUNCTION

I2CON.7

RDAT

Read: the most recently received data bit.

“

CXA

Write: clears the transmit active flag.

I2CON.6

ATN

Read: ATN = 1 if any of the flags DRDY, ARL, STP, or STP = 1.

“

IDLE

Write: in the I2C slave mode, writing a 1 to this bit causes the I2C hardware to ignore the bus until it

is needed again.

I2CON.5

DRDY

Read: Data Ready flag, set when there is a rising edge on SCL.

“

CDR

Write: writing a 1 to this bit clears the DRDY flag.

I2CON.4

ARL

Read: Arbitration Loss flag, set when arbitration is lost while in the transmit mode.

“

CARL

Write: writing a 1 to this bit clears the CARL flag.

I2CON.3

STR

Read: Start flag, set when a start condition is detected at a master or non-idle slave.

“

CSTR

Write: writing a 1 to this bit clears the STR flag.

I2CON.2

STP

Read: Stop flag, set when a stop condition is detected at a master or non-idle slave.

“

CSTP

Write: writing a 1 to this bit clears the STP flag.

I2CON.1

MASTER

Read: indicates whether this device is currently as bus master.

“

XSTR

Write: writing a 1 to this bit causes a repeated start condition to be generated.

I2CON.0

—

Read: undefined.

“

XSTP

Write: writing a 1 to this bit causes a stop condition to be generated.

* Due to the manner in which bit addressing is implemented in the 80C51 family, the I2CON register should never be altered by

use of the SETB, CLR, CPL, MOV (bit), or JBC instructions. This is due to the fact that read and write functions of this register

are different. Testing of I2CON bits via the JB and JNB instructions is supported.

—

SU01155

MASTER

STP

STR

ARL

DRDY

ATN

RDAT

I2CON

Reset Value: 81h

Bit Addressable*

Address: D8h

XSTP

XSTR

CSTP

CSTR

CARL

CDR

IDLE

CXA

READ

WRITE

Figure 9. I2C Control Register (I2CON)

BIT

SYMBOL

FUNCTION

I2DAT.7

RDAT

Read: the most recently received data bit, captured from SDA at every rising edge of SCL. Reading

I2DAT also clears DRDY and the Transmit Active state.

“

XDAT

Write: sets the data for the next transmitted bit. Writing I2DAT also clears DRDY and sets the

Transmit Active state.

I2DAT.6–0

–

Unused.

—

SU01156

—

RDAT

I2DAT

Reset Value: xxh

Not Bit Addressable

Address: D9h

—

XDAT

READ

WRITE

Figure 10. I2C Data Register (I2DAT)

87LPC769 датащи(PDF) 21 Page - NXP Semiconductors

87LPC769 датащи(HTML) 21 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61

датащи скачать

ссылки URL