AMWS

Vishay Phoenix

Wirewound/Metal Film Resistors,

Commercial Power, Axial Lead

www.vishay.com

For technical questions, contact: ww2aresistors@vishay.com

Document Number: 30250

5

Revision: 19-Feb-08

End-of-Life Vishay Phoenix Product

TESTS AND REQUIREMENTS

Essentially all tests and requirements present in table below, follow the schedule of IEC standard publication 60115-1, 60015-4,

60068.

PERFORMANCE

IEC

60115-1

CLAUSE

IEC

60068

TEST

METHOD

TEST

PROCEDURE

REQUIREMENTS

4.6.1.1

-

Insulation resistance

500 VDC during 1 min;

V-block method

Rins min. 100 MΩ

4.7

-

Voltage proof on

insulation

1000 VRMS during 1 min;

V-block method

No breakdown or flashover

4.8

-

Temperature

coefficient

Between

- 55 °C at + 275 °C

R < 10

Ω

R

≥ 10 Ω

0 to + 600 ppm/°C;

+ 150 to - 100 ppm/°C

4.13

-

Short time overload

Dissipation 10 x Pn; 5 s

ΔR/R

max. ± 2 % + 0.05 Ω

4.16

21(U)

Robustness of

terminations:

No visible damage

ΔR/R

max. ± 2 % + 0.05 Ω

4.16.2

21(Ua1)

Tensile all samples

Load 10 N; 10 s

4.16.3

21(Ub)

Bending half number

of samples

Load 5 N; 4 x 90°

4.16.4

21(Uc)

Tension other half

of samples

3 x 360° in

opposite directions

4.17

20(Ta)

Solderability

(after aging)

16 h at 155 °C;

leads immersed in flux 600,

leads immersed 2 mm

for 2 ± 0.5 s

in a solder bath at 235 ± 5 °C

Good tinning;

no damage

ΔR/R

max. ± 0.5 % + 0.05 Ω

4.18

20(Tb)

Resistance to

soldering heat

Thermal shock: 3 s,

350 °C; 6 mm from body

ΔR/R

max. ± 4 % + 0.05 Ω

4.19

14(Na)

Rapid change of

temperature

30 min at - 55 °C and

30 min + 275 °C;

5 cycles

No visual damage

ΔR/R

max. ± 5 % + 0.05 Ω

4.23

Climatic sequence:

ΔR/R

max. ± 3 % + 0.05 Ω

4.23.2

2(Ba)

Dry heat

16 h, 275 °C

4.23.3

30(Db)

Damp heat

(accelerated)

1st cycle

24 h, 25 °C to 55 °C;

90 to 100 % RH

4.23.4

1(Aa)

Cold

2 h, - 65 °C

4.23.6

30 (Db)

Damp heat

(accelerated)

remaining cycles

6 days; 55 °C;

90 to 98 % RH

4.24

3 (Ca)

Damp heat

(steady state)

56 days; 40 °C; 90 to 95 % RH;

loaded with 0.01 Pn

ΔR/R

max. ± 5 % + 0.05 Ω

4.25.1

-

Endurance

40 °C

1000 h load

with Pn or Vmax.;

1.5 h ON and

0.5 h OFF

No damage

ΔR/R

max. ± 5 % + 0.1 Ω