VS-301MT...C Series

www.vishay.com

Vishay Semiconductors

Revision: 16-Feb-2022

2

Document Number: 96991

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• Table shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC

FORWARD CONDUCTION

PARAMETER

SYMBOL

TEST CONDITIONS

VALUES

UNITS

Maximum DC output current

at case temperature

IO

120° rect. conduction angle

300

A

100

°C

Maximum peak, one-cycle forward,

non-repetitive surge current

IFSM

t = 10 ms

No voltage

reapplied

Initial

TJ = TJ maximum

2400

A

t = 8.3 ms

2512

t = 10 ms

100 % VRRM

reapplied

2018

t = 8.3 ms

2113

Maximum I2t for fusing

I2t

t = 10 ms

No voltage

reapplied

28 795

A2s

t = 8.3 ms

26 285

t = 10 ms

100 % VRRM

reapplied

20 360

t = 8.3 ms

18 590

Maximum I2

√t for fusing

I2

√t

t = 0.1 ms to 10 ms, no voltage reapplied

287 955

A2

√s

Low level value of threshold voltage

VFT(TO)1

(16.7 % x

π x IF(AV) < I < π x IF(AV)),

TJ maximum

0.79

V

High level value of threshold voltage

VFT(TO)2

(I >

π x IF(AV)), TJ maximum

0.96

Low level value of forward slope resistance

rf1

16.7 % x

π x IF(AV) < I < π x IF(AV)),

TJ maximum

3.36

m

Ω

High level of forward slope resistance

rf2

(I >

π x IF(AV)), TJ maximum

3.22

Maximum forward voltage drop

VFM

Ipk = 240 A, TJ = 25 °C, per junction

1.54

V

Ipk = 300 A, TJ = 25 °C, per junction

1.7

RMS isolation voltage

VISOL

TJ = 25 °C, all terminal shorted

f = 50 Hz, t = 1 s

3600

THERMAL AND MECHANICAL SPECIFICATIONS

PARAMETER

SYMBOL

TEST CONDITIONS

VALUES

UNITS

Maximum junction operating

TJ

-40 to +150

°C

Maximum storage temperature

TStg

-40 to +125

Maximum thermal resistance,

junction to case

RthJC

DC operation per module

0.038

°C/W

DC operation per junction

0.23

Typical thermal resistance,

case to heat sink

RthCS

Per module

Mounting surface smooth, flat, and greased

0.03

Mounting

torque ± 15 %

to heat sink

A mounting compound is recommended and the torque should be

rechecked after a period of 3 hours to allow for the spread of the

compound. Lubricated threads.

5

Nm

to terminal

5

Approximate weight

235

g

ΔR CONDUCTION PER JUNCTION

DEVICES

SINE HALF WAVE CONDUCTION

RECTANGULAR WAVE CONDUCTION

UNITS

180°

120°

90°

60°

30°

180°

120°

90°

60°

30°

VS-301MT...C Series

0.044

0.050

0.061

0.087

0.143

0.029

0.050

0.066

0.091

0.145

°C/W