HT82K95A datasheet(15/48 Pages) HOLTEK

15 / 48 page

HT82K95E/HT82K95A

Rev. 1.20

October 24, 2005

Using the internal clock source, there is only 1 reference

time-base for Timer/Event Counter 0. The internal clock

source is coming from fSYS/4.

The external clock input allows the user to count exter-

nal events, measure time intervals or pulse widths.

Using the internal clock source, there is only 1 reference

time-base for Timer/Event Counter 1. The internal clock

source is coming from fSYS/4. The external clock input

allows the user to count external events, measure time

intervals or pulse widths.

There are 2 registers related to the Timer/Event Counter

0; TMR0 ([0DH]), TMR0C ([0EH]). Two physical regis-

ters are mapped to TMR0 location; writing TMR0 makes

the starting value be placed in the Timer/Event Counter

0 preload register and reading TMR0 gets the contents

of the Timer/Event Counter 0. The TMR0C is a

timer/event counter control register, which defines some

options.

There are 3 registers related to Timer/Event Counter 1;

TMR1H (0FH), TMR1L (10H), TMR1C (11H). Writing

TMR1L will only put the written data to an internal

lower-order byte buffer (8 bits) and writing TMR1H will

transfer the specified data and the contents of the

lower-order byte buffer to TMR1H and TMR1L preload

registers, respectively. The Timer/Event Counter 1

preload register is changed by each writing TMR1H op-

erations. Reading TMR1H will latch the contents of

TMR1H and TMR1L counters to the destination and the

lower-order byte buffer, respectively. Reading the

TMR1L will read the contents of the lower-order byte

buffer. The TMR1C is the Timer/Event Counter 1 control

able or disable and active edge.

The TM0, TM1 bits define the operating mode. The

event count mode is used to count external events,

which means the clock source comes from an external

(TMR0/TMR1) pin. The timer mode functions as a nor-

mal timer with the clock source coming from the fSYS/4

(Timer0/Timer1). The pulse width measurement mode

can be used to count the high or low level duration of the

external signal (TMR0/TMR1). The counting is based on

the fSYS/4 (Timer0/Timer1).

In the event count or timer mode, once the Timer/Event

Counter 0/1 starts counting, it will count from the current

contents in the Timer/Event Counter 0/1 to FFH or

FFFFH. Once overflow occurs, the counter is reloaded

from the Timer/Event Counter 0/1 preload register and

generates the interrupt request flag (T0F/T1F; bit 5/6 of

INTC) at the same time.

In the pulse width measurement mode with the TON

and TE bits equal to one, once the TMR0/TMR1 has re-

ceived a transient from low to high (or high to low if the

TE bits is

²0²) it will start counting until the TMR0/TMR1

returns to the original level and resets the TON. The

measured result will remain in the Timer/Event Counter

0/1 even if the activated transient occurs again. In other

words, only one cycle measurement can be done. Until

setting the TON, the cycle measurement will function

again as long as it receives further transient pulse. Note

that, in this operating mode, the Timer/Event Counter

0/1 starts counting not according to the logic level but

according to the transient edges. In the case of counter

overflows, the counter 0/1 is reloaded from the

Timer/Event Counter 0/1 preload register and issues the

interrupt request just like the other two modes. To en-

able the counting operation, the timer ON bit (TON; bit 4

T M 1

T M 0

T M R 0

T E

T M 1

T M 0

T O N

P u l s e W i d t h

M e a s u r e m e n t

M o d e C o n t r o l

T i m e r / E v e n t C o u n t e r 0

P r e l o a d R e g i s t e r

T i m e r / E v e n t

C o u n t e r 0

D a t a B u s

R e l o a d

O v e r f l o w

t o I n t e r r u p t

f S Y S / 4

Timer/Event Counter 0

T M 1

T M 0

T M R 1

T E

T M 1

T M 0

T O N

P u l s e W i d t h

M e a s u r e m e n t

M o d e C o n t r o l

1 6 B i t s

T i m e r / E v e n t C o u n t e r

P r e l o a d R e g i s t e r

D a t a B u s

R e l o a d

O v e r f l o w

t o I n t e r r u p t

f S Y S / 4

1 6 B i t s

T i m e r / E v e n t C o u n t e r

( T M R 1 H / T M R 1 L )

L o w B y t e

B u f f e r

Timer/Event Counter 1

HT82K95A датащи(PDF) 15 Page - Holtek Semiconductor Inc

HT82K95A датащи(HTML) 15 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

датащи скачать

ссылки URL