MODEL: R3S-DAC16

R3S-DAC16 SPECIFICATIONS

ES-8933 Rev.4 Page 1/9

http://www.m-system.co.jp/

Remote I/O R3 Series

DISCRETE INPUT OUTPUT MODULE

(Di 8 points, Do 8 points, tension clamp terminal block)

Typical Applications

• Controls start/stop of field devices with ON/OFF control

output

• Simplifies signal hold circuit of field devices

• Utilizing One-Shot Output reduces the load of PLC side.

27.5 (1.08)

130 (5.12)

120 (4.72)

mm (inch)

MODEL: R3S-DAC16[1][2]

ORDERING INFORMATION

• Code number: R3S-DAC16[1][2]

Specify a code from below for each [1] and [2].

(e.g. R3S-DAC16W/Q)

• Specify the specification for option code /Q

(e.g. /C01)

NO. OF CHANNELS

16: 16 points (8 input, 8 output)

[1] COMMUNICATION MODE

S: Single

W: Dual

[2] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

CAUTION

• This unit is not designed to be used with the following

types of interface modules (models: R3-NC2, R3-NEIP1, R3-

NFx, R3-NLx).

• Output completion status data is compatible with interface

modules (models: R3-NC1, R3-NC3, R3-NDx, R3-NE1, R3-

NFL1, R3-NM1, R3-NM4, R3-NP1) of firmware version V2.00

or higher, and interface modules (models: R3-NM3, R3-

NML3) of firmware version V1.00 or higher.

GENERAL SPECIFICATIONS

Connection

Internal bus: Via the Installation Base (model: R3-BSx)

I/O: Separable tension clamp terminal

mm)

Internal Power: Via the Installation Base (model: R3-BSx)

Isolation: Input to output to internal bus or internal power

Output mode setting: One-Shot Output Mode, ON/OFF

Control Output Mode, Continuance Output Mode selectable

with DIP switch

Data length Setting: 8bit, 4bit selectable with DIP switch

(For ON/OFF Control Output Mode only)

One-shot ON time setting: 0.1 to 25.6 sec. selectable with

DIP switch

ON/OFF control output setting: Swappable its pair with DIP

switch.

Output hold setting: Setting for communication error with

side DIP SW

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/ green) LED;

Green in normal operating conditions

Red with the abnormal configuration

Status indicator: Red LED;

1 to 8: Intput status, turns on with input ON.

9 to 16: Output status, turns on with output ON.

Di read rate setting: 1 / 5 / 10 / 20 / 50 / 70 / 100 / 200

msec. selectable with DIP SW

INPUT SPECIFICATIONS

Number of input: 8 points

Isolation: Optical isolator

Input resistance: Approx. 4.4 kΩ

Common: Positive or negative (NPN/PNP) common per 8

points (2 terminals)

ON voltage/current: ≥ 11 V, ≥ 2.5 mA

OFF voltage/current: ≤ 6 V, ≤ 1.3 mA

■ Dry Contact input