MODEL: R5-RS

R5-RS SPECIFICATIONS

ES-6114 Rev.14 Page 1/3

http://www.m-system.co.jp/

Remote I/O R5 Series

RTD INPUT MODULE

96.5

(3.80)

18 (.71)

90

(3.54)

mm (inch)

MODEL: R5-RS[1][2][3]

ORDERING INFORMATION

• Code number: R5-RS[1][2][3]

Specify a code from below for each [1] through [3].

(e.g. R5-RS2W/Q)

• Specify the specification for option code /Q

(e.g. /C01)

[1] NO. OF CHANNELS

1: 1 channel

2: 2 channels

[2] COMMUNICATION MODE

S: Single

W: Dual

[3] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

GENERAL SPECIFICATIONS

Connection

Internal bus: Via the Installation Base (model: R5-BS)

Input: Euro type connector terminal

stripped length 7 mm)

Internal power: Via the base (model: R5-BS)

Isolation: Input 1 to input 2 to internal bus or internal power

Sensor type: Selectable with the side DIP SW

Temperature unit: °C, °F or absolute temperature selectable

with the side DIP SW

Burnout detection: Upscale or downscale selectable with the

side DIP SW

Linearization: Standard

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

INPUT SPECIFICATIONS

Maximum leadwire resistance: 200 Ω per wire (3-wire)

Sensing current: ≤ 1 mA

Temperature range

RTD

°C

USABLE RANGE

CONFORMANCE RANGE

Cu 10 @25°C

Cu 50

JPt 100 (JIS ’89)

-212 to +312

-100 to +200

-236 to +560

-50 to +250

-50 to +150

-200 to +510

Pt 100 (JIS ’89)

Pt 100 (JIS ’97, IEC)(*)

Pt 1000

-240 to +900

-240 to +900

-240 to +900

-200 to +660

-200 to +850

-200 to +850

Pt 50Ω (JIS ’81)

Ni 100

Ni 508.4Ω

-236 to +700

-100 to +252

-100 to +332

-200 to +649

-80 to +250

-50 to +200

RTD

°F

USABLE RANGE

CONFORMANCE RANGE

Cu 10 @25°C

Cu 50

JPt 100 (JIS ’89)

-350 to +594

-148 to +392

-393 to +1040

-58 to +482

-58 to +302

-328 to +950

Pt 100 (JIS ’89)

Pt 100 (JIS ’97, IEC)(*)

Pt 1000

-400 to +1652

-400 to +1652

-400 to +1652

-328 to +1220

-328 to +1562

-328 to +1562

Pt 50Ω (JIS ’81)

Ni 100

Ni 508.4Ω

-393 to +1292

-148 to +486

-148 to +630

-328 to +1200

-112 to +482

-58 to +392

(*) Factory setting.

Max. (upscale) or min. (downscale) value of the usable

range when a burnout is detected.

INSTALLATION

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R5-BS)

Weight: 100 g (3.53 oz)