F340X2 datasheet(4/12 Pages) VISHAY

4 / 12 page

F340X2 305VAC

www.vishay.com

Vishay BCcomponents

Revision: 11-Oct-2019

Document Number: 26074

For technical questions, contact: rfi@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

MOUNTING

Normal Use

The capacitor unit is designed for mounting on printed-circuit boards. The capacitors packed in bandoleers are designed for

mounting in printed-circuit boards by means of automatic insertion machines.

For detailed tape specifications refer to packaging information www.vishay.com/docs?28139

Specific Method of Mounting to Withstand Vibration and Shock

The capacitor unit is designed for mounting on a printed-circuit board. In order to withstand vibration and shock tests, it must

be ensured that the stand-off pips are in good contact with the printed-circuit board. The capacitor shall be mechanically fixed

by the leads and the body clamped.

Dimensions Tolerances

For the maximum product dimensions for length (lmax.), width (wmax.), and height (hmax.) use the following tolerances:

lmax. = l + l, wmax. = w + w, and hmax. = h + h

• For products with pitch = 27.5 mm,

w = l = h = 0.7 mm

• For products with pitch = 37.5 mm,

w = l = h = 0.7 mm

• For products with pitch = 52.5 mm,

w = l = h = 1.0 mm

For the minimum product dimensions for length (lmin.), width (wmin.) and height (hmin.) following tolerances of the components

are valid:

lmin. = l - l, wmin. = w - w, and hmin. = h - h

• For products with pitch = 27.5 mm,

w = l = h = 1.0 mm

• For products with pitch = 37.5 mm,

w = l = h = 1.0 mm

• For products with pitch = 52.5 mm,

w = l = h = 1.5 mm

Space Requirements for Printed-Circuit Board

For product height with seating plane as given by “IEC 60717” as reference.

The maximum space for length (lmax.), width (wmax.), and height (hmax.) of film capacitors to take in account on the printed-circuit

board is shown in the drawings.

• For products with pitch = 27.5 mm,

w = l = h = 0.7 mm

• For products with pitch = 37.5 mm,

w = l = h = 0.7 mm

• For products with pitch = 52.5 mm,

w = l = h = 1.0 mm

Eccentricity defined as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product

concerned.

The maximum length and width of film capacitors is shown in the figure:

SOLDERING CONDITIONS

For general soldering conditions and wave soldering profile we refer to the document “Soldering Guidelines for Film

Capacitors”: www.vishay.com/doc?28171

STORAGE TEMPERATURE

Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation

RATINGS AND CHARACTERISTICS REFERENCE CONDITIONS

Unless otherwise specified. all electrical values apply to an ambient temperature of 23 °C ± 1°C. an atmospheric pressure of

86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %.

For reference testing. a conditioning period shall be applied over 96 hours ± 4 hours by heating the products in a circulating air

oven at the rated temperature and a relative humidity not exceeding 20 %.

CBA116

Eccentricity

max. = w + Δw

max. = h + Δh

max. = I + ΔI

Seating plane

F340X2 датащи(PDF) 4 Page - Vishay Siliconix

F340X2 датащи(HTML) 4 Page - Vishay Siliconix

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

датащи скачать

ссылки URL