Preliminary Factsheet 00.100

January 2020

These specifications are subject to change without notice.

01/10/2020

© 2020 Greenliant

1

S71488-01

GLS FS0019 Rev. 00

GLS86FC016G2 / 032G2 / 064G2 / 128G2

Industrial Temp mSATA ArmourDrive™ MX Series

Features

• Industry Standard SATA Host Interface

–

SATA 1.5Gb/s, 3Gb/s and 6Gb/s

–

SATA Revision 3.2

–

ATA/ATAPI-8 compliant

–

Supports 48-bit address feature set

–

Native Command Queuing (NCQ)

up to 32 commands

• Performance

–

Sequential data read: Up to 410 MB/s

–

Sequential data write: Up to 115 MB/s

(measured using 128KB transfer size)

• Power Management

–

3.3V power supply

–

Host initialized power management (HIPM)

–

Device initialized power management (DIPM)

• Power Consumption

–

Active mode:

–

128GB: Up to 2860mW

–

64GB: Up to 1980mW

–

32GB: Up to 1540mW

–

16GB: Up to 1200mW

–

Idle / Standby mode: <355mW

–

DevSleep mode: <70mW

• Reliability

–

Mean Time Between Failures (MTBF):

2 million hours*

• Expanded Data Protection

–

Added data security through user-selectable

protection zones

–

Secure Erase (data sanitization)

• 20-Byte Serial Number

–

Factory pre-programmed unique ID

–

User-programmable 10-Byte ID

• Supports TRIM and SMART Commands

• Robust Built-in ECC

• Thermal Throttling

• NAND Configuration

–

2 bits per cell (3D MLC NAND)

• Endurance

–

Program/Erase (P/E) Cycles: 5K

• Operating Temperature Range

–

Industrial: -40°C to 85°C

• JEDEC standard MO-300 mSATA form factor

–

29.85 mm x 50.80 mm x 4.85 mm

• All Devices are RoHS Compliant

*Estimate based on preliminary component reliability data

Product Description

The GLS86FC016G2 / 032G2 / 064G2 / 128G2

Industrial

Temperature

miniSATA

(mSATA)

ArmourDrive™ MX Series modules (referred to as

“mSATA ArmourDrive” in this factsheet) are high-

reliability solid state drives. They include a 16, 32, 64

or 128 GByte SATA NANDrive™ on a printed circuit

board (PCB).

mSATA ArmourDrive is ideal for applications that

require removable form factor and more reliable data

storage. mSATA solid state storage technology is

widely used in industrial computers, set-top boxes,

test

and

measurement

instrumentation,

multi-

functional printers, medical equipment, security and

surveillance systems, network servers and digital

signage. These removable solid state drives (SSDs)

surpass traditional hard disk drives (HDDs) in their

small size, security, reliability, ruggedness and low

power consumption.

The NAND flash controller with built-in advanced

NAND management firmware communicates with the

host through the standard SATA protocol. It does not

require any additional or proprietary software such as

the Flash File System (FFS) and Memory Technology

Driver (MTD). The firmware effectively optimizes the

use of NAND flash memory’s program/erase (P/E)

cycles and minimizes write amplification.

mSATA ArmourDrive is pre-programmed with a 10-

Byte unique serial ID

and has the option of

programming an additional 10-Byte serial ID for even

greater system security.

mSATA ArmourDrive’s advanced NAND management

technology

improves

endurance,

enhances

data

security and helps prevent data corruption during

unexpected power failure events. This innovative

technology combines robust NAND flash controller

hardware error correction capabilities with advanced

wear-leveling algorithms and bad block management

to improve data reliability and significantly extend the

life of the product.

mSATA ArmourDrive is available in a standard

JEDEC 52-pin PCB module form factor.