Factsheet 04.100

July 2018

These specifications are subject to change without notice.

07/10/2018

© 2018 Greenliant

1

S71432-F

GLS85LS1002P / 1004P / 1008P

Industrial Grade

Features

• Industry Standard Serial ATA (SATA) Host

Interface

-

SATA 1.5Gb/s

1)

-

ATA/ATAPI-8 compliant

-

Supports 48-bit address feature set

• Performance

-

Sequential data read:

Up to 70 MByte/sec*

-

Sequential data write:

Up to 60 MByte/sec*

* measured using 128 KByte transfer size

• Power Management

-

3.3V and 1.2Vpower supply

-

Host SATA interface power management

-

Immediate disabling of unused circuitry

without host intervention

-

Active mode:

750mW typical (GLS85LS1008P)

560mW typical (GLS85LS1004P)

450mW typical (GLS85LS1002P)

-

Idle / Standby mode:

210mW typical

-

Sleep mode:

70mW typical

• Integrated Voltage Detector

-

Detects supply voltage fluctuations and

generates reset during power-up and power-

down to prevent inadvertent writes

• Supports SMART Commands

• Expanded Data Protection

-

Added data security through user-selectable

protection zones

• 20-Byte Serial Number

-

Factory pre-programmed 10-Byte unique ID

-

User-programmable 10-Byte ID

• Robust Built-in ECC

• NAND Configuration

-

1 bit per cell (SLC)

• Industrial Temperature Range

-

-40°C to 85°C

• FBGA package

-

14.0 mm x 24.0 mm x 1.95 mm, 145-ball,

1.0 mm ball pitch, FZJE

• All Devices are RoHS Compliant

1)

Current product revision supports SATA Revision 1.x with

host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5Gb/s).

2)

For management of the Sleep Mode, refer to “SATA

NANDrive Application Design Guide.”

Product Description

The GLS85LS1002P / 1004P / 1008P Industrial Grade

SATA NANDrive™ devices (referred to as “SATA

NANDrive” in this factsheet) are fully integrated solid

state drives. They combine an advanced Greenliant

NAND controller and 2, 4 or 8 GByte of NAND flash in

a multi-chip package. These products are ideal for

embedded and portable applications that require

smaller form-factor and more reliable data storage.

SATA-interface solid state mass storage technology is

widely used in portable and industrial computers, set-

top boxes, multi-functional printers, point-of-sales

terminals,

video

and

audio

recorders,

medical

instruments and car infotainment systems.

SATA NANDrive is a single device, solid state drive

(SSD) that provides the functionality and compatibility

of a complete SATA hard disk drive (HDD) in a 14 mm

x 24 mm BGA package for easy, space saving

mounting to a system motherboard. These products

surpass traditional storage in their small size, security,

reliability, ruggedness and low power consumption.

The integrated NAND flash controller with built-in

advanced

NAND

management

firmware

communicates with the host through the standard

SATA protocol. It does not require any additional or

proprietary software such as the Flash File System

(FFS) and Memory Technology Driver (MTD).

SATA NANDrive is pre-programmed with a 10-Byte

unique serial ID and has the option of programming

an additional 10-Byte serial ID for even greater

system security.

SATA NANDrive’s advanced NAND management

technology enhances data reliability and security,

improves endurance and accurately estimates the

remaining life of the NAND flash devices. This

innovative

technology

combines

robust

NAND

controller hardware error correction capabilities with

advanced wear-leveling algorithms and bad block

management to significantly extend the life of the

product.

SATA NANDrive devices are offered in a 145-ball

BGA, 1 mm ball pitch package.