4. Performance & Typical Physical Properties

Colors Available:

White

Extension/compression:

Capability of ±10%

Application Temperature Range:

40° to 122°F (4° to 50°C)

Flame Spread 5

Smoke Development 5

STC Acoustic Barrier

56 when tested in STC 56 rated

(ASTM E 90 and ASTM E 413)

:

wall assembly

5. Storage & Shelf Life

Storage:

Shelf Life:

above 68°F (20°C) and below 90°F (32.2°C).

Lot numbering: First to sixth digit = Date of Production (MMDDYY)

Seventh indicator = dash symbol (-) Eighth digit = shift number

6. Installation Techniques

Consult a 3M Authorized Fire Protection Products Distributor / Dealer or Sales Representative for applicable drawings and details.

Sound Sealant SS 100. Ensure that the surface of the substrates are not wet and are free from dust, debris and frost. Sealant can

be installed with a standard caulking gun, pneumatic pumping equipment or it can be easily applied with a putty knife or trowel.

Installation Details: Install the applicable depth of backing material, if required, as detailed within the applicable 3M design. Install the applicable

all tools immediately after use with water.

Limitations:

building materials that bleed oil, plasticizers or solvent (e.g. impregnated wood, oil-based sealants, or green or partially-vulcanized

immersed in water.

NOTICE: This product is not for use as a commercial firestop. This product is not acceptable for use with chlorinated

polyvinylchloride (CPVC) pipes.

7. Maintenance

Sound Sealant SS 100 is damaged, the following procedure will apply: remove and reinstall the damaged section in accordance with the applicable

8. Availability

9. Safe Handling Information

Consult product’s Material Safety Data Sheet (MSDS) prior to handling and disposal.

Important Notice to User:

Technical Information: The technical information, recommendations and other statements contained in this document are subject to change, the accuracy or completeness of

such information is not guaranteed.

Product Use: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of

a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M

product and determining whether it is fit for a particular purpose and suitable for user’s method of application.

Warranty and Limited Remedy: 3M warrants that each 3M Fire

Protection Product will be free from defects in material and manufacture for 90 days from the date of purchase from 3M’s authorized distributor. 3M MAKES NO OTHER EXPRESS

OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If a 3M product does not conform to this

warranty, the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.

Limitation of Liability: Except where prohibited by

law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted.

Building and Commercial

Services Division

3M Center, Building 223-2N-21

St. Paul, MN 55144-1000 USA

1-800-328-1687

www.3M.com/firestop

3M is a trademark of 3M. Used under license in Canada. LEED is a trademark

of U.S. Green Building Council Non-Profit Corporation. All other trademarks are

the property of their respective owners.

Hardness (ASTM D 2240 Shore A):

60

Tensile Strength:

175 psi (1.2 MPa)

39.5%

<250 g/L

Dry: Under typical conditions of 75°F (23°C) and 50% R.H., sealant

becomes tack-free in about ten minutes and dry-to-touch in 30 to 60 minutes.

Full dry depends upon ambient conditions and volume of sealant. Typical dry

rate is approximately 1/8 inch (3mm) per day.

Meets the intent of LEED® VOC environmental quality requirements.

Please Recycle. Printed in U.S.A.

© 3M 2013. All rights reserved.

98-0213-4661-8