T22

www.vishay.com

Vishay

Revision: 13-May-2020

6

Document Number: 40187

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ENVIRONMENTAL CHARACTERISTICS

ITEM

CONDITION

POST TEST PERFORMANCE

Stability at low and

high temperatures

As specified in MIL-PRF-39006

The capacitors shall meet the requirements of MIL-PRF-39006

Seal

MIL-PRF-39006



Method 112 of MIL-STD-202,



conditions A and C

When the capacitors are tested as specified in MIL-PRF-39006,

there shall be no evidence of leakage.

Moisture resistance

MIL-PRF-55365



Method 106 of MIL-STD-202,



number of cycles: 10 continuous cycles except

that steps 7a and 7b shall be omitted.

DC leakage



Capacitance change



ESR

Not exceed 125 % of the specified value



Within ±10 % of the initial measured value



Not exceed the specified value

Barometric pressure

(reduced)

Method 105 of MIL-STD-202, condition E



(150 000 feet) (45,720.1 m).

There shall be no mechanical or visual damage to capacitors

post-conditioning.

Low temperature

storage

MIL-PRF-39006



Method 502 of MIL-STD-810,



Storage temperature: - 62 °C + 0 °C, - 3 °C

Exposure time: 72 h followed by a 1 h exposure

at + 125 °C + 7 °C, - 0 °C within 24 h after low

temperature storage.

DC leakage



Capacitance change



ESR

Not to exceed 125 % of the specified value



Within ± 10 % of the initial measured value



Not exceed the specified value

Salt atmosphere

(corrosion)

MIL-PRF-39006



Method 101 of MIL-STD-202,



condition B (48 h), applicable salt solution: 5 %

There shall be no harmful corrosion. Marking shall remain legible.

MECHANICAL PERFORMANCE CHARACTERISTICS

ITEM

CONDITION

POST TEST PERFORMANCE

Shear test

AEC-Q200-006



Apply a pressure load of 5 N for 10 s ± 1 s

horizontally to the center of capacitor



side body.

DC leakage



Capacitance change



ESR

Not to exceed 125 % of the specified value



Within ± 10 % of the initial measured value



Not exceed the specified value

There shall be no mechanical or visual damage to capacitors

post-conditioning.

Solderability

MIL-STD-202, method 208, test B



ANSI/J-STD-002:



SnPb solder - test B



Pb-free solder - test B1

All terminations shall exhibit a continuous solder coating free



from defects for a minimum of 95 % of the critical area of any

individual lead.

Resistance



to solvent

MIL-STD-202, method 215

There shall be no mechanical or visual damage to capacitors

post-conditioning. Marking shall remain legible, no degradation



of the can material.

Insulation

resistance

Method 302 of MIL-STD-202, condition B



The insulation resistance shall be not less than 100 M

.

The capacitors shall meet the requirements of MIL-PRF-39006.

Shock



(specified pulse)

MIL-STD-202, method 213,condition D (500 g)

The capacitors shall meet the requirements of MIL-PRF-39006.

Vibration,



high frequency

MIL-STD-202, method 204, condition H



(80 g peak)

The capacitors shall meet the requirements of MIL-PRF-39006.

Random vibration

MIL-STD-202, method 214, condition II-G



(overall RMS 27.78 G)

The capacitors shall meet the requirements of MIL-PRF-39006.

Thermal shock

MIL-STD-202, method 107, condition A

Thermal shock shall be in accordance with MIL-PRF-39006 when

tested for 300 cycles.

Resistance to

soldering heat

MIL-STD-202, method 210, condition J,



except with only one heat cycle

Capacitance change



ESR



Leakage current

Within ± 10 % of initial



Initial specified value or less



Initial specified value or less

There shall be no mechanical or visual damage to capacitors

post-conditioning.