ISO6741 datasheet(7/35 Pages) TI

7 / 35 page

6.6 Insulation Specifications

PARAMETER

TEST CONDITIONS

VALUE

UNIT

DW-16

CLR

External clearance(1)

Shortest terminal-to-terminal distance through air

CPG

External creepage(1)

Shortest terminal-to-terminal distance across the

package surface

DTI

Distance through the insulation

Minimum internal gap (internal clearance)

>17

CTI

Comparative tracking index

DIN EN 60112 (VDE 0303-11); IEC 60112

>600

Material group

According to IEC 60664-1

Overvoltage category per IEC 60664-1

Rated mains voltage ≤ 600 VRMS

I-IV

Rated mains voltage ≤ 1000 VRMS

I-III

DIN VDE V 0884-11:2017-01(2)

VIORM

Maximum repetitive peak isolation voltage

AC voltage (bipolar)

1500

VPK

VIOWM

Maximum working isolation voltage

AC voltage; Time dependent dielectric breakdown

(TDDB) Test; See Figure 9-5

1060

VRMS

DC voltage

1500

VDC

VIOTM

Maximum transient isolation voltage

VTEST = VIOTM,

t = 60 s (qualification);

VTEST = 1.2 x VIOTM,

t= 1 s (100% production)

7071

VPK

VIOSM

Maximum surge isolation voltage(3)

Test method per IEC 62368-1, 1.2/50 µs waveform,

VTEST = 1.6 x VIOSM (qualification)

6250

VPK

qpd

Apparent charge(4)

Method a, After Input-output safety test subgroup 2/3,

Vini = VIOTM, tini = 60 s;

Vpd(m) = 1.2 x VIORM, tm = 10 s

≤5

Method a, After environmental tests subgroup 1,

Vini = VIOTM, tini = 60 s;

Vpd(m) = 1.6 x VIORM, tm = 10 s

≤5

Method b1; At routine test (100% production) and

preconditioning (type test)

Vini = 1.2 x VIOTM, tini = 1 s;

Vpd(m) = 1.875 x VIORM, tm = 1 s

≤5

CIO

Barrier capacitance, input to output(5)

VIO = 0.4 x sin (2πft), f = 1 MHz

RIO

Isolation resistance(5)

VIO = 500 V, TA = 25°C

>1012

VIO = 500 V, 100°C ≤ TA ≤ 125°C

>1011

VIO = 500 V at TS = 150°C

>109

Pollution degree

Climatic category

40/125/21

UL 1577

VISO

Maximum withstanding isolation voltage

VTEST = VISO , t = 60 s (qualification),

VTEST = 1.2 x VISO , t = 1 s (100% production)

5000

VRMS

(1)

Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application.

Care should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the

isolator on the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in

certain cases. Techniques such as inserting grooves and/or ribs on a printed-circuit board are used to help increase these

specifications.

(2)

This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured

by means of suitable protective circuits.

(3)

Testing is carried out in air or oil to determine the intrinsic surge immunity of the isolation barrier.

(4)

Apparent charge is electrical discharge caused by a partial discharge (pd).

(5)

All pins on each side of the barrier tied together creating a two-terminal device.

www.ti.com

ISO6741

SLLSFJ6 – AUGUST 2020

Submit Document Feedback

Product Folder Links: ISO6741

ISO6741 датащи(PDF) 7 Page - Texas Instruments

ISO6741 датащи(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

датащи скачать

ссылки URL