AM29LV033MU datasheet(34/56 Pages) AMD

34 / 56 page

Am29LV033MU

November 11, 2002

ADV ANCE

I N FO RMAT I O N

Figure 9.

Toggle Bit Algorithm

DQ2: Toggle Bit II

The “Toggle Bit II” on DQ2, when used with DQ6, indi-

cates whether a particular sector is actively erasing

(that is, the Embedded Erase algorithm is in progress),

or whether that sector is erase-suspended. Toggle Bit

II is valid after the rising edge of the final WE# pulse in

the command sequence.

DQ2 toggles when the system reads at addresses

within those sectors that have been selected for era-

sure. (The system may use either OE# or CE# to con-

trol the read cycles.) But DQ2 cannot distinguish

whether the sector is actively erasing or is erase-sus-

pended. DQ6, by comparison, indicates whether the

device is actively erasing, or is in Erase Suspend, but

cannot distinguish which sectors are selected for era-

sure. Thus, both status bits are required for sector and

mode information. Refer to Table 11 to compare out-

puts for DQ2 and DQ6.

Figure 9 shows the toggle bit algorithm in flowchart

form, and the section “DQ2: Toggle Bit II” explains the

algorithm. See also the DQ6: Toggle Bit I subsection.

Figure 21 shows the toggle bit timing diagram. Figure

22 shows the differences between DQ2 and DQ6 in

graphical form.

Reading Toggle Bits DQ6/DQ2

Refer to Figure 9 for the following discussion. When-

ever the system initially begins reading toggle bit sta-

tus, it must read DQ7–DQ0 at least twice in a row to

determine whether a toggle bit is toggling. Typically,

the system would note and store the value of the tog-

gle bit after the first read. After the second read, the

system would compare the new value of the toggle bit

with the first. If the toggle bit is not toggling, the device

has completed the program or erase operation. The

system can read array data on DQ7–DQ0 on the fol-

lowing read cycle.

However, if after the initial two read cycles, the system

determines that the toggle bit is still toggling, the sys-

tem also should note whether the value of DQ5 is high

(see the section on DQ5). If it is, the system should

then determine again whether the toggle bit is tog-

gling, since the toggle bit may have stopped toggling

just as DQ5 went high. If the toggle bit is no longer

toggling, the device has successfully completed the

program or erase operation. If it is still toggling, the de-

vice did not completed the operation successfully, and

the system must write the reset command to return to

reading array data.

The remaining scenario is that the system initially de-

termines that the toggle bit is toggling and DQ5 has

not gone high. The system may continue to monitor

the toggle bit and DQ5 through successive read cy-

cles, determining the status as described in the previ-

ous paragraph. Alternatively, it may choose to perform

START

Yes

DQ5 = 1?

Yes

Toggle Bit

= Toggle?

Program/Erase

Operation Not

Complete, Write

Reset Command

Program/Erase

Operation Complete

Read DQ7–DQ0

Toggle Bit

= Toggle?

Read DQ7–DQ0

Twice

Read DQ7–DQ0

Note: The system should recheck the toggle bit even if

DQ5 = “1” because the toggle bit may stop toggling as DQ5

changes to “1.” See the subsections on DQ6 and DQ2 for

more information.

AM29LV033MU датащи(PDF) 34 Page - Advanced Micro Devices

AM29LV033MU датащи(HTML) 34 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

датащи скачать

ссылки URL