AM29DL642G datasheet(22/54 Pages) AMD

22 / 54 page

Am29DL642G

June 10, 2005

PRELIMINARY

The alternate method intended only for programming

equipment requires V

ID on address pin A9 and OE#.

This method is compatible with programmer routines

written for earlier 3.0 volt-only AMD flash devices.

The device is shipped with all sectors unprotected.

AMD offers the option of programming and protecting

sectors at its factory prior to shipping the device

through AMD’s ExpressFlash™ Service. Contact an

AMD representative for details.

It is possible to determine whether a sector is pro-

tected or unprotected. See the Autoselect Mode sec-

tion for details.

Write Protect (WP#)

The Write Protect function provides a hardware

method of protecting without using VID. This function is

one of two provided by the WP#/ACC pin.

If the system asserts V

IL on the WP#/ACC pin, the de-

vice disables program and erase functions in sectors

0, 1, 140, and 141, independently of whether those

sectors were protected or unprotected using the

method described in “Sector/Sector Block Protection

and Unprotection”.

If the system asserts VIH on the WP#/ACC pin, the de-

vice reverts to whether sectors 0, 1, 140, and 141

were last set to be protected or unprotected. That is,

sector protection or unprotection for these sectors de-

pends on whether they were last protected or unpro-

tected using the method described in “Sector/Sector

Block Protection and Unprotection”.

Note that the WP#/ACC pin must not be left floating or

unconnected; inconsistent behavior of the device may

result.

Table 8.

WP#/ACC Modes

Temporary Sector Unprotect

(Note: For the following discussion, the term “sector”

applies to both sectors and sector blocks. A sector

block consists of two or more adjacent sectors that are

protected or unprotected at the same time (see Table

7).

This feature allows temporary unprotection of previ-

ously protected sectors to change data in-system. The

Sector Unprotect mode is activated by setting the RE-

SET# pin to V

ID. During this mode, formerly protected

sectors can be programmed or erased by selecting the

sector addresses. Once V

ID is removed from the RE-

SET# pin, all the previously protected sectors are

protected again. Figure 1 shows the algorithm, and

Figure 22 shows the timing diagrams, for this feature.

If the WP#/ACC pin is at V

IL, sectors 0, 1, 140, and

141 will remain protected during the Temporary sector

Unprotect mode.

Figure 1.

Temporary Sector Unprotect Operation

WP# Input

Voltage

Device

Mode

Disables programming and erasing in

SA0, SA1, SA140, and SA141

Enables programming and erasing in

SA0, SA1, SA140, and SA141

Enables accelerated progamming (ACC).

See “Accelerated Program Operation” on

page 10..

START

Perform Erase or

Program Operations

RESET# = V

Temporary Sector

Unprotect Completed

(Note 2)

RESET# = V

(Note 1)

Notes:

1. All protected sectors unprotected (If WP#/ACC = V

IL,

sectors 0, 1, 140, and 141 will remain protected).

2. All previously protected sectors are protected once

again.

AM29DL642G датащи(PDF) 22 Page - Advanced Micro Devices

AM29DL642G датащи(HTML) 22 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

датащи скачать

ссылки URL