AM79C930VCW datasheet(101/161 Pages) AMD

101 / 161 page

P R E L I M I N A R Y

AMD

101

Am79C930

TIR24: TCR Index Register

This register is the TCR Index register. This register is

used as an address into indirect TAI register space. The

value in the TCR Index Register is used as an address

that points at one of 64 registers that are accessed

through the TCR Data Port.

Bit

Name

Reset Value

Description

7:6

Reserved

–

Reserved. Must be written as a 0. Reads of this bit produce

undefined data.

5:0

TCRI[5:0]

00h

TCR Index value. The value in the TCR Index Register is used as an

address that points at one of 64 registers that are accessed through

the TCR Data Port.

TIR25: Configuration Data Port

This register is the Configuration Data Port register.

This register is used as the data port allowing access

to 64 indirectly accessed registers. The register that is

accessed through the Configuration Data Port is deter-

mined by the current setting of the Configuration Index

Bit

Name

Reset Value

Description

7–0

CD[7:0]

–

Configuration Register Data. This register is used as the data port

allowing access to 64 indirectly accessed registers. The register

that is accessed through the Configuration Data Port is determined

by the current setting of the Configuration Index Register.

TIR26: Antenna Diversity and A/D Control

This register is the Antenna Diversity and A/D

Control register.

Bit

Name

Reset Value

Description

CHBSY

Channel Busy. The Am79C930 device will set this bit to a 1 when

the clear channel assessment logic determines that a carrier is pre-

sent. The Am79C930 device will set this bit to a 0 when the clear

channel assessment logic determines that a carrier is not present.

Writes by firmware will have no effect on this bit.

ANTLOK

Antenna Selection Locked. The Am79C930 device will set

ANTLOK to a 1 when it has determined that criteria for antenna se-

lection have been passed. The Am79C930 device will set ANTLOK

to a 0 when the RXS bit of TIR16 is set 1.

ANTSLT

Antenna Selection. This bit gives the current value of the ANTSLT

pin, whether determined by register bit programming or internal an-

tenna selection logic. This bit is read only.

ANTS

Antenna Switch. If ANTSEN is set to 1, then the software may di-

rectly control the value of the ANTSLT and

ANTSLT pins with this

bit. If ANTSEN is set to 0, then writes to this bit will have no effect on

the value of the ANTSLT and

ANTSLT pins. Note: Antenna diversity

is disabled with the ANTSEN bit (bit 3 of TIR26).

ANTSEN

Antenna Switch Enable. ANTSEN and ANTSLTLFN (TCR30[7])

are combined with the PCMCIA pin setting to determine the func-

tionality of the ANTSLT and

ANTSLT pins.

The complete control of the function of the ANTSLT and

ANTSLT

pins are described in the

Multi-Function Pin section.

AM79C930VCW датащи(PDF) 101 Page - Advanced Micro Devices

AM79C930VCW датащи(HTML) 101 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL