 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
MLCC-LD датащи(PDF) 9 Page - AVX Corporation |
|
|
|||||||||||||||||||||||||||||
MLCC-LD датащи(HTML) 9 Page - AVX Corporation |
|
|
9 / 14 page  47 MLCC Tin/Lead Termination “B” 112916 Parameter/Test X7R Specification Limits Measuring Conditions Operating Temperature Range -55ºC to +125ºC Temperature Cycle Chamber Capacitance Within specified tolerance Freq.: 1.0 kHz ± 10% Voltage: 1.0Vrms ± .2V Dissipation Factor ≤ 10% for ≥ 50V DC rating ≤ 12.5% for 25V DC rating ≤ 12.5% for 25V and 16V DC rating ≤ 12.5% for ≤ 10V DC rating Insulation Resistance 100,000MΩ or 1000MΩ - μF, whichever is less Charge device with rated voltage for 120 ± 5 secs @ room temp/humidity Dielectric Strength No breakdown or visual defects Charge device with 250% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Note: Charge device with 150% of rated voltage for 500V devices. Resistance to Flexure Stresses Appearance No defects Deflection: 2mm Test Time: 30 seconds Capacitance Variation ≤ ±12% Dissipation Factor Meets Initial Values (As Above) Insulation Resistance ≥ Initial Value x 0.3 Solderability ≥ 95% of each terminal should be covered with fresh solder Dip device in eutectic solder at 230 ± 5ºC for 5.0 ± 0.5 seconds Resistance to Solder Heat Appearance No defects, <25% leaching of either end terminal Dip device in eutectic solder at 260ºC for 60 seconds. Store at room temperature for 24 ± 2 hours before measuring electrical properties. Capacitance Variation ≤ ±7.5% Dissipation Factor Meets Initial Values (As Above) Insulation Resistance Meets Initial Values (As Above) Dielectric Strength Meets Initial Values (As Above) Thermal Shock Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes Capacitance Variation ≤ ±7.5% Step 2: Room Temp ≤ 3 minutes Dissipation Factor Meets Initial Values (As Above) Step 3: +125ºC ± 2º 30 ± 3 minutes Insulation Resistance Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes Dielectric Strength Meets Initial Values (As Above) Repeat for 5 cycles and measure after 24 ± 2 hours at room temperature Load Life Appearance No visual defects Charge device with 1.5 rated voltage (≤ 10V) in test chamber set at 125ºC ± 2ºC for 1000 hours (+48, -0) Remove from test chamber and stabilize at room temperature for 24 ± 2 hours before measuring. Capacitance Variation ≤ ±12.5% Dissipation Factor ≤ Initial Value x 2.0 (See Above) Insulation Resistance ≥ Initial Value x 0.3 (See Above) Dielectric Strength Meets Initial Values (As Above) Load Humidity Appearance No visual defects Store in a test chamber set at 85ºC ± 2ºC/ 85% ± 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. Remove from chamber and stabilize at room temperature and humidity for 24 ± 2 hours before measuring. Capacitance Variation ≤ ±12.5% Dissipation Factor ≤ Initial Value x 2.0 (See Above) Insulation Resistance ≥ Initial Value x 0.3 (See Above) Dielectric Strength Meets Initial Values (As Above) Specifications and Test Methods X7R – |
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
